|
|
4H3-0370-000CN is represented by #12 in the diagram below.
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 1
- 1 XA9-1386-000CN - M3 X 8mm long self threading screw with captured washer
- 4
- 4 FU5-0428-000CN - 30-tooth gear - Runs on the timing belt on the finisher lower roller next to the 20-tooth pulley
- 5
- 5 FU5-0454-000CN - 40-tooth gear - Runs on the swing press shaft assembly - Located between torque limiter and bushing on the rear side plate of the finisher
- 8
- 8 FM2-1417-000CN - Sensor/switch assembly - Includes leaf spring, micro switch (MSW31), photo interrupter (PI32), and wire saddle
- 11
- 11 FC5-3657-000CN - Torque limiter - Torque limiter for the swing press shaft
- 12
- 12 4H3-0370-000CN - Electromagnetic shutter clutch (CL31) connector (J1046)
- 12 4H3-0370-000CN - Electromagnetic shutter clutch (CL31) connector (J1046)
1
XA9-1386-000CN
Screw
M3 X 8mm long self threading screw with captured washer
1
XA9-1386-000CN
Screw
M3 X 8mm long self threading screw with captured washer
4
FU5-0428-000CN
Gear
30-tooth gear - Runs on the timing belt on the finisher lower roller next to the 20-tooth pulley
5
FU5-0454-000CN
Gear
40-tooth gear - Runs on the swing press shaft assembly - Located between torque limiter and bushing on the rear side plate of the finisher
8
FM2-1417-000CN
Sensor
Sensor/switch assembly - Includes leaf spring, micro switch (MSW31), photo interrupter (PI32), and wire saddle
11
FC5-3657-000CN
Torque Limiter
Torque limiter - Torque limiter for the swing press shaft
12
4H3-0370-000CN
Clutch
Electromagnetic shutter clutch (CL31) connector (J1046)
12
4H3-0370-000CN
Clutch
Electromagnetic shutter clutch (CL31) connector (J1046)
|
|