|
|
WG8-5624-000CN is represented by #6 in the diagram below.
Internal Components
- 1
- 1 RC1-0268-000CN - Metal rod between external power button and switch on power supply board
- 4
- 4 RU5-0045-020CN - 18 tooth gear - Located on right side of printer in the Tray 2 paper pickup assembly
- 5
- 5 RL1-0264-000CN - Gear - Gear with attached shaft - Driven by pickup drive assembly on right front of printer
- 6
- 6 WG8-5624-000CN - Replacement for part WG8-5362-000CN ORDER WG8-5624-000CN PHOTO-INTERRUPTER TLP1241 Photo-sensor (TLP1241) - Sensor flag activated
- 6 WG8-5624-000CN - Replacement for part WG8-5362-000CN ORDER WG8-5624-000CN PHOTO-INTERRUPTER TLP1241 Photo-sensor (TLP1241) - Sensor flag activated
- 7
- 7 RU5-0040-000CN - Gear - 23 tooth gear in lower front section of pickup drive assembly
- 8
- 8 RC1-0206-000CN - Bushing - On right side of paper pickup drive assembly
- 8
- 8 RC1-0206-000CN - Bushing - On right side of paper pickup drive assembly
- 9
- 9 RM1-1067-000CN - Replacement for part RM1-1067-000CN Laser/scanner assembly for 4250/4350 series LaserJet printers
- 9 RM1-1067-030CN - Replacement for part RM1-1067-000CN Laser/scanner assembly for 4250/4350 series LaserJet printers
- 10
- 10 RC1-0264-000CN - Feed roller shaft bushing - Bushing on right side of printer that supports the feed roller shaft.
- 11
- 11 RM1-1198-000CN - Laser cable - Connects between DC Controller board and laser scanner unit - J145 to J83
- 12
- 12 XA9-1500-000CN - M3 pan-head Phillips screw with flat washer - 8mm long
- 14
- 14 RM1-0036-000CN - Paper pickup roller - Gray spongy rubber roller on a white cylinder and 24 tooth white gear on one side. Paper pickup roller - For Tray 2, 3 or 4 paper cassette
- 14 RM1-0036-020CN - Paper pickup roller - Gray spongy rubber roller on a white cylinder and 24-tooth white gear on one side
- 15
- 15 RM1-0037-020CN - Paper feed/seperation roller assembly - Black rubber roller on a blue plastic cylinder
- 17
- 17 RC1-0209-000CN - Paper sensor flag for Tray 2 paper pickup assembly
- 17 RC1-0209-020CN - Paper sensor flag for Tray 2 paper pickup assembly
- 18
- 18 RC1-0243-000CN - Right front power supply guide - Attaches to right side of printer chassis
- 19
- 19 RC1-3352-000CN - Paper pickup arm - Pickup and feed roller holder for Tray 2 paper pickup assembly
- 20
- 20 RC1-0212-000CN - Paper pickup arm holder - Holder for pickup roller shaft
- 21
- 21 RC1-0371-000CN - 23 Gear - Gear that drives paper feed roller - Attaches to feed roller shaft
- 23
- 23 RC1-0213-000CN - Compression spring - Provides pressure for paper pickup and feed rollers in Tray 2 pickup assembly
- 25
- 25 RC1-0330-020CN - Solenoid damper - Locate on right side of Tray 2 guide - Works with kicker to dampen Tray 2 pickup solenoid on right side of tray guide
- 26
- 26 RM1-1192-000CN - Power cable for Tray 3 paper feeder - Black connector with 42mm six wire cable to white connector
- 27
- 27 RL1-0015-000CN - Kicker assembly - Mounts to right side of the printer and is connected to the right side guide - Senses when the paper cassette is inserted into the printer
- 28
- 28 RM1-0041-020CN - Tray 2 paper size tray sensing assembly - White plastic tray size sensing fingers and microswitch assembly
- 29
- 29 RB1-8107-000CN - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
- 30
- 30 RC1-0242-000CN - Inner right side edge guard - Small plastic guard that protects wires inside chassis on right side of printer.
- 31
- 31 RC1-0244-000CN - Support guide - Supports right rear side of power supply board
- 32
- 32 RC1-0247-000CN - Right side edge guard - Small plastic guard that protects wires - Mounts on right outer side of printer chassis.
- 33
- 33 XA9-1503-000CN - M3 truss head (Flanged) phillips screw (Black oxide finish) - 6mm long
- 34
- 34 RM1-0042-000CN - Accessory cable/connector - Connector for stacker and stacker/stapler accessory at top right rear of printer
- 35
- 35 5851-2766 - Swing plate assembly kit - For Tray 2 paper lift assembly - Located between the main gear assembly and the fuser, just above the power supply - Contains swing plate assembly and new fuser pressure release gear
- 35 RM1-0043-060CN - Swing plate assembly - Pressure Roller GearSwing plate assembly - For tray 2 paper lift assembly Located between the main gear assembly and the fuser, just above the power supply. swing plate assembly usually comes with black and white large gears.
- 37
- 37 RM1-1193-000CN - Envelope feeder cable - From DC Controller board to envelope feeder connector - Includes envelope feeder connector
- 38
- 38 RC1-0254-000CN - Torsion spring - Provides tension for Tray 2 kicker - Mounts on Tray 2 guide assembly
- 39
- 39 RC1-1923-000CN - Torsion spring - Provides tension for paper sensor flag
- 41
- 41 RM1-0034-070CN - Paper pick-up assembly - Paper pickup drive assembly for tray 2 input tray - Does not include the 18-tooth gear - In order to install this part the 18-tooth gear must be removed and replaced
1
RC1-0268-000CN
Rod
Metal rod between external power button and switch on power supply board
4
RU5-0045-020CN
Gear
18 tooth gear - Located on right side of printer in the Tray 2 paper pickup assembly
5
RL1-0264-000CN
Gear
Gear - Gear with attached shaft - Driven by pickup drive assembly on right front of printer
6
WG8-5624-000CN
Sensor
Replacement for part WG8-5362-000CN ORDER WG8-5624-000CN PHOTO-INTERRUPTER TLP1241 Photo-sensor (TLP1241) - Sensor flag activated
6
WG8-5624-000CN
Sensor
Replacement for part WG8-5362-000CN ORDER WG8-5624-000CN PHOTO-INTERRUPTER TLP1241 Photo-sensor (TLP1241) - Sensor flag activated
7
RU5-0040-000CN
Gear
Gear - 23 tooth gear in lower front section of pickup drive assembly
8
RC1-0206-000CN
Bushing
Bushing - On right side of paper pickup drive assembly
8
RC1-0206-000CN
Bushing
Bushing - On right side of paper pickup drive assembly
9
RM1-1067-000CN
Laser Scanner
Replacement for part RM1-1067-000CN Laser/scanner assembly for 4250/4350 series LaserJet printers
9
RM1-1067-030CN
Laser Scanner
Replacement for part RM1-1067-000CN Laser/scanner assembly for 4250/4350 series LaserJet printers
10
RC1-0264-000CN
Bushing
Feed roller shaft bushing - Bushing on right side of printer that supports the feed roller shaft.
11
RM1-1198-000CN
Cable
Laser cable - Connects between DC Controller board and laser scanner unit - J145 to J83
14
RM1-0036-000CN
Roller
Paper pickup roller - Gray spongy rubber roller on a white cylinder and 24 tooth white gear on one side. Paper pickup roller - For Tray 2, 3 or 4 paper cassette
14
RM1-0036-020CN
Roller
Paper pickup roller - Gray spongy rubber roller on a white cylinder and 24-tooth white gear on one side
15
RM1-0037-020CN
Roller
Paper feed/seperation roller assembly - Black rubber roller on a blue plastic cylinder
18
RC1-0243-000CN
Guide
Right front power supply guide - Attaches to right side of printer chassis
19
RC1-3352-000CN
Holder
Paper pickup arm - Pickup and feed roller holder for Tray 2 paper pickup assembly
20
RC1-0212-000CN
Holder
Paper pickup arm holder - Holder for pickup roller shaft
21
RC1-0371-000CN
Gear
23 Gear - Gear that drives paper feed roller - Attaches to feed roller shaft
23
RC1-0213-000CN
Spring
Compression spring - Provides pressure for paper pickup and feed rollers in Tray 2 pickup assembly
25
RC1-0330-020CN
Damper
Solenoid damper - Locate on right side of Tray 2 guide - Works with kicker to dampen Tray 2 pickup solenoid on right side of tray guide
26
RM1-1192-000CN
Cable
Power cable for Tray 3 paper feeder - Black connector with 42mm six wire cable to white connector
27
RL1-0015-000CN
Flag
Kicker assembly - Mounts to right side of the printer and is connected to the right side guide - Senses when the paper cassette is inserted into the printer
28
RM1-0041-020CN
Sensor
Tray 2 paper size tray sensing assembly - White plastic tray size sensing fingers and microswitch assembly
29
RB1-8107-000CN
Foot
Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
30
RC1-0242-000CN
Guard
Inner right side edge guard - Small plastic guard that protects wires inside chassis on right side of printer.
31
RC1-0244-000CN
Guide
Support guide - Supports right rear side of power supply board
32
RC1-0247-000CN
Guard
Right side edge guard - Small plastic guard that protects wires - Mounts on right outer side of printer chassis.
33
XA9-1503-000CN
Screw
M3 truss head (Flanged) phillips screw (Black oxide finish) - 6mm long
34
RM1-0042-000CN
Connector
Accessory cable/connector - Connector for stacker and stacker/stapler accessory at top right rear of printer
35
5851-2766
Lever
Swing plate assembly kit - For Tray 2 paper lift assembly - Located between the main gear assembly and the fuser, just above the power supply - Contains swing plate assembly and new fuser pressure release gear
35
RM1-0043-060CN
Lever
Swing plate assembly - Pressure Roller GearSwing plate assembly - For tray 2 paper lift assembly Located between the main gear assembly and the fuser, just above the power supply. swing plate assembly usually comes with black and white large gears.
37
RM1-1193-000CN
Cable
Envelope feeder cable - From DC Controller board to envelope feeder connector - Includes envelope feeder connector
38
RC1-0254-000CN
Spring
Torsion spring - Provides tension for Tray 2 kicker - Mounts on Tray 2 guide assembly
39
RC1-1923-000CN
Spring
Torsion spring - Provides tension for paper sensor flag
41
RM1-0034-070CN
Pickup Assembly
Paper pick-up assembly - Paper pickup drive assembly for tray 2 input tray - Does not include the 18-tooth gear - In order to install this part the 18-tooth gear must be removed and replaced
|
|