RC1-9900-000CN printer parts diagram.

12
 

RC1-9900-000CN is represented by #27 in the diagram below.

Input-tray main body
RC1-9900-000CN is represented by #27 in the diagram below.
  • 7
    • 7 RC1-9883-000CN - Lock lever - This is the rear cover lock for the 1 x 500-sheet paper input tray
  • 9
    • 9 RK2-1331-000CN - Stepping motor - Main drive motor for the printer - Motor M1
  • 10
  • 11
    • 11 RS5-9099-000CN - Stepped screw - Larger shoulder screw used to fasten the left side cover to the frame of the 2,000-sheet paper feeder assembly (two used)
  • 12
    • 12 VS1-7257-012CN - Drawer Connector (J1903) - For the 1 x 500-sheet input tray
  • 15
    • 15 WT2-5738-000CN - Cable holder - Secures cable at left front side near DC controller board - White plastic stand-off/holder
  • 17
    • 17 XA9-1469-000CN - Machine screw with attached washer - M3, 10mm - Used to hold plastic to metal
  • 18
    • 18 RM1-3537-000CN - 3 x 500-sheet paper input tray right door assembly
  • 19
  • 23
    • 23 RM1-3575-000CN - Paper pick-up option cable - Used for the 1 x 500-sheet input tray
  • 25
  • 26
    • 26 RC1-9896-000CN - Double lock front caster - For the 1 x 500-sheet paper input tray
  • 27
    • 27 RC1-9900-000CN - Lock shaft support - Located on the 1 x 500-sheet paper input tray
  • 28
    • 28 RC1-9901-000CN - Switch cover plate - For the 1 x 500-sheet paper input tray door open detection switch (SW103)
  • 29
    • 29 RC1-9912-000CN - Lock shaft - For the 1 x 500-sheet paper input tray
  • 30
    • 30 RC1-9913-000CN - Lock arm - For the 1 x 500-sheet paper input tray - Mounts on the lock shaft
  • 31
    • 31 RC1-9915-000CN - Bushing - Mounts on the lock shaft next to the arm lock on the 1 x 500-sheet paper input tray
  • 32
    • 32 RC1-9917-000CN - Stationary rear caster - Mounts on the bottom frame of the 500-sheet high capacity input (HCI) paper feeder assembly
  • 33
    • 33 RL1-1310-000CN - Right cassette rail - For the 1 x 500-sheet paper input tray
  • 36
    • 36 XA9-0912-000CN - Machine screw with captured washer - M5 X 12 - Typically used to secure plastic parts to metal
1
RC1-9871-000CN Cover 1 x 500-sheet paper input tray rear cover
2
RC1-9872-000CN Cover 1 x 500-sheet paper input tray left cover
3
RC1-9873-000CN Cover 1 x 500-sheet paper input tray upper front cover
4
RC1-9874-000CN Cover 1 x 500-sheet paper input tray lower right cover
5
RC1-9881-000CN Guide 1 x 500-sheet input tray paper feed roller guide
6
RC1-9882-000CN Stop Stopper, right door
7
RC1-9883-000CN Lever Lock lever - This is the rear cover lock for the 1 x 500-sheet paper input tray
8
RC1-9884-000CN Door 1 x 500-sheet paper input tray tape door
9
RK2-1331-000CN Motor Stepping motor - Main drive motor for the printer - Motor M1
10
RL1-1321-000CN Cover 3 x 500-sheet paper input tray right front cover
11
RS5-9099-000CN Screw Stepped screw - Larger shoulder screw used to fasten the left side cover to the frame of the 2,000-sheet paper feeder assembly (two used)
12
VS1-7257-012CN Connector Drawer Connector (J1903) - For the 1 x 500-sheet input tray
14
WT2-5694-000CN Clamp Snap-in cable clamp
15
WT2-5738-000CN Holder Cable holder - Secures cable at left front side near DC controller board - White plastic stand-off/holder
16
XA9-1448-000CN Screw Screw - M4 X 8mm long
17
XA9-1469-000CN Screw Machine screw with attached washer - M3, 10mm - Used to hold plastic to metal
18
RM1-3537-000CN Door 3 x 500-sheet paper input tray right door assembly
19
RM1-3569-000CN PC Board 1 x 500-sheet input tray paper feed PCA assembly
20
RM1-3571-000CN Cable Paper pick-up option drawer cable
21
RM1-3572-000CN Cable Pick-up option door switch cable
22
RM1-3574-000CN Cable Option sensor PCA connect cable
23
RM1-3575-000CN Cable Paper pick-up option cable - Used for the 1 x 500-sheet input tray
24
RM1-3573-000CN Cable Pick-up option PCA connect cable
25
RC1-9231-000CN Rail Roller rail - Attaches to the left cassette rail
26
RC1-9896-000CN Caster Double lock front caster - For the 1 x 500-sheet paper input tray
27
RC1-9900-000CN Support Lock shaft support - Located on the 1 x 500-sheet paper input tray
28
RC1-9901-000CN Plate Switch cover plate - For the 1 x 500-sheet paper input tray door open detection switch (SW103)
29
RC1-9912-000CN Shaft Lock shaft - For the 1 x 500-sheet paper input tray
30
RC1-9913-000CN Arm Lock arm - For the 1 x 500-sheet paper input tray - Mounts on the lock shaft
31
RC1-9915-000CN Bushing Bushing - Mounts on the lock shaft next to the arm lock on the 1 x 500-sheet paper input tray
32
RC1-9917-000CN Caster Stationary rear caster - Mounts on the bottom frame of the 500-sheet high capacity input (HCI) paper feeder assembly
33
RL1-1310-000CN Rail Right cassette rail - For the 1 x 500-sheet paper input tray
34
RL1-1311-000CN Rail Paper cassette tray left rail
35
WC2-5512-000CN Switch Door open detection switch (SW103)
36
XA9-0912-000CN Screw Machine screw with captured washer - M5 X 12 - Typically used to secure plastic parts to metal
37
XA9-1448-000CN Screw Screw - M4 X 8mm long
38
RC1-9921-000CN Door Stock door - For 1 x 500-sheet paper input tray
12
  • Social Media
  • Product Reviews
  • Service Blog
  • Follow Us:
  • Facebook  Linked In  Twitter  YoutTube  Google+
iTonerPlust
Copyright© 2024 Toner2Print Inc. All rights reserved. All prices and specifications are subject to change without notice.
Toner2Print Inc. is not responsible for typographical errors. All typographical errors are subject to correction.