C6426-20011 printer parts diagram.

C6426-20011 is represented by #11 in the diagram below.

• 2
  • 2 C6426-00015 - Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker

• 5
  • 5 C4557-00009 - Separator spring - Provides pressure between separator assembly and the center drive roller

• 6
  • 6 C6426-00003 - IEC connector bracket - Holds the power cord socket

• 7
  • 7 C6426-40102 - Separator Peg - Pushes up the separator pad during the paper pick operation

• 8
  • 8 C4557-40015 - Rear roller (Black) - Between paper and rear paper guide

• 8
  • 8 C4557-40015 - Rear roller (Black) - Between paper and rear paper guide

• 9
  • 9 C4557-20003 - Rear roller spring - Flexible axle for rear roller

• 9
  • 9 C4557-20003 - Rear roller spring - Flexible axle for rear roller

• 10
  • 10 C6426-00004 - Upper paper guide support - Support bracket which attaches to the print mech frame for mounting the upper paper guide

• 11
  • 11 C6426-20011 - Rod spring - Installed on right side of backbone

• 12
  • 12 C5870-00002 - Service station ESD grounding clip

• 13
  • 13 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)

• 13
  • 13 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)

• 13
  • 13 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)

• 13
  • 13 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)

• 14
  • 14 C6409-00009 - Backbone - Large metal item attached to the front of the printer base

• 15
  • 15 C6426-60058 - Interconnect PC board - Small square PC board with 4 contact pads for the duplexer module
  • 15 C8154-60073 - Interconnect PC board - Small square PC board with four contact pads for the duplexer module

• 16
  • 16 C4557-60011 - Separator pad for HP DeskJet 700 Series

• 17
  • 17 C6426-40100 - Separator peg lifter - Used to lift and retain the separator peg under spring tension - Caution: if this part is installed incorrectly, printer will NOT function

• 18
  • 18 C6409-00011 - Encoder spring - Provides tension for encoder strip

• 19
  • 19 C6426-00001 - Upper rail for HP DeskJet 952C

• 20
  • 20 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 20
  • 20 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 20
  • 20 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 20
  • 20 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 21
  • 21 C6409-20002 - Rod mounting clip

• 22
  • 22 C4557-40021 - Feed roller idler gear

• 23
  • 23 C6426-40103 - Kicker bar cam gear - Gear with cam lobe and offset pin

• 24
  • 24 C6426-40118 - Kicker bar - Restacks paper in paper input tray stack after the top sheet is picked

• 25
  • 25 C6429-60025 - Kicker bar cam link (spring loaded)

• 26
  • 26 C6426-00017 - Lifter spring - Provides upper tension on the kicker bar (cam follower) lift plate

• 28
  • 28 C6426-40098 - Lower paper guide housing (Does NOT include any attaching parts)

• 29
  • 29 C6429-60141 - Inner paper guide (Includes antistatic brush) - Guides the paper through the print mech and over the upper paper guide