C4557-40118 printer parts diagram.

C4557-40118 is represented by #23 in the diagram below.

• 1
  • 1 C4557-40130 - Left wall brace - Provides support for left wall

• 2
  • 2 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 2
  • 2 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 2
  • 2 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 2
  • 2 C4557-20007 - Pinch spring - Provides tension on upper paper guide

• 3
  • 3 C4557-40128 - Left backbone brace - Provides support for backbone

• 4
  • 4 C6409-00008 - Upper paper guide support - Base for upper paper guide

• 6
  • 6 C4557-60011 - Separator pad for HP DeskJet 700 Series

• 7
  • 7 C5870-40029 - Separator peg for HP DeskJet 895C

• 8
  • 8 C4557-00009 - Separator spring - Provides pressure between separator assembly and the center drive roller

• 9
  • 9 C4557-40020 - Lower guide - Platform for seperator peg, spring and pad

• 10
  • 10 C4557-20003 - Rear roller spring - Flexible axle for rear roller

• 10
  • 10 C4557-20003 - Rear roller spring - Flexible axle for rear roller

• 12
  • 12 C4557-40085 - Link pin for HP Color Copier 160

• 13
  • 13 C4557-00033 - Link spring - Provides tension to shaft of pick cam gear

• 14
  • 14 C4557-40084 - Pivot link for HP Color Copier 270

• 15
  • 15 C6409-40040 - Pick cam - Controls pressure plate and lever

• 16
  • 16 C4557-40021 - Feed roller idler gear

• 17
  • 17 C5870-20002 - Paper stacker (kicker) spring

• 18
  • 18 C4557-40016 - Kicker - Restacks paper in stack after top sheet is picked

• 19
  • 19 C4557-00037 - Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker

• 20
  • 20 C4557-40063 - Separator lifter - Used to lift the separator peg

• 21
  • 21 C5870-40020 - Right backbone brace - Installed on right side of printer base to provide support for backbone

• 22
  • 22 C5870-00002 - Service station ESD grounding clip

• 23
  • 23 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)

• 24
  • 24 C6409-00013 - BacKBone - Large metal item where the main logic PCA and the carriage drive motor are mounted - This item should be replaced only by trained, experienced service personnel

• 25
  • 25 C5870-00004 - Wear strip - Long, spring loaded strip mounted in top of backbone - Used to ensure smooth ink cartridge carriage motion

• 26
  • 26 C4557-20028 - EOR tension spring - Maintains tension on wear strip

• 27
  • 27 C4557-40150 - Pivot snap - Used to hold pivot to pick feed roller shaft

• 28
  • 28 C4557-80019 - Paper motor encoder disk

• 29
  • 29 C4557-40095 - Encoder gear for HP Color Copier 260
  • 29 C4557-60025 - Pivot feed roller - Shaft with 4 hard rollers - Does not include other items such as gear or encoder
  • 29 C6409-60037 - Pivot feed roller assembly - Shaft with small rollers and paper encoder - This item should be replaced only by trained, experienced service personnel

• 30
  • 30 C4557-20024 - Shifter spring - Provides tension on the pivot

• 31
  • 31 C5870-40030 - Pivot assembly - Large plastic Item below the feed roller assembly - Picks and feeds media through print mechanism - Should be replaced only by experienced service personnel

• 32
  • 32 C4557-00035 - Paper pusher spring - Maintains alignment in paper tray

• 32
  • 32 C4557-00035 - Paper pusher spring - Maintains alignment in paper tray

• 33
  • 33 C5870-40022 - Paper pusher - Small, spring loaded lever attached to pivot - Pushes against left side of paper to maintain right edge alignment

• 33
  • 33 C5870-40022 - Paper pusher - Small, spring loaded lever attached to pivot - Pushes against left side of paper to maintain right edge alignment