|
|
C4557-40021 is represented by #14 in the diagram below.
- 3
- 3 C6426-00015 - Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker
- 5
- 5 C6426-20011 - Rod spring - Installed on right side of backbone
- 7
- 7 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
- 7
- 7 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
- 7
- 7 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
- 7
- 7 C4557-40118 - Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
- 8
- 8 C6409-00009 - Backbone - Large metal item attached to the front of the printer base
- 9
- 9 C6426-60058 - Interconnect PC board - Small square PC board with 4 contact pads for the duplexer module
- 9 C8154-60073 - Interconnect PC board - Small square PC board with four contact pads for the duplexer module
- 10
- 10 C6426-40100 - Separator peg lifter - Used to lift and retain the separator peg under spring tension - Caution: if this part is installed incorrectly, printer will NOT function
- 11
- 11 C6409-00011 - Encoder spring - Provides tension for encoder strip
- 13
- 13 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 13
- 13 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 13
- 13 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 13
- 13 C4557-20007 - Pinch spring - Provides tension on upper paper guide
- 15
- 15 C6426-40103 - Kicker bar cam gear - Gear with cam lobe and offset pin
- 16
- 16 C6426-40118 - Kicker bar - Restacks paper in paper input tray stack after the top sheet is picked
- 18
- 18 C6426-00017 - Lifter spring - Provides upper tension on the kicker bar (cam follower) lift plate
- 19
- 19 C6426-40098 - Lower paper guide housing (Does NOT include any attaching parts)
- 20
- 20 C6429-60141 - Inner paper guide (Includes antistatic brush) - Guides the paper through the print mech and over the upper paper guide
- 21
- 21 C4557-00009 - Separator spring - Provides pressure between separator assembly and the center drive roller
- 22
- 22 C6426-00003 - IEC connector bracket - Holds the power cord socket
- 23
- 23 C6426-40102 - Separator Peg - Pushes up the separator pad during the paper pick operation
- 24
- 24 C4557-40015 - Rear roller (Black) - Between paper and rear paper guide
- 24
- 24 C4557-40015 - Rear roller (Black) - Between paper and rear paper guide
- 25
- 25 C4557-20003 - Rear roller spring - Flexible axle for rear roller
- 25
- 25 C4557-20003 - Rear roller spring - Flexible axle for rear roller
- 26
- 26 C6426-00004 - Upper paper guide support - Support bracket which attaches to the print mech frame for mounting the upper paper guide
- 27
- 27 C4557-60011 - Separator pad for HP DeskJet 700 Series
3
C6426-00015
Lever
Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker
5
C6426-20011
Spring
Rod spring - Installed on right side of backbone
7
C4557-40118
Foot
Rubber foot - Replacement rubber foot for the bottom of the printer (four used)
8
C6409-00009
Backbone
Backbone - Large metal item attached to the front of the printer base
9
C6426-60058
PC Board
Interconnect PC board - Small square PC board with 4 contact pads for the duplexer module
9
C8154-60073
PC Board
Interconnect PC board - Small square PC board with four contact pads for the duplexer module
10
C6426-40100
Lifter
Separator peg lifter - Used to lift and retain the separator peg under spring tension - Caution: if this part is installed incorrectly, printer will NOT function
11
C6409-00011
Spring
Encoder spring - Provides tension for encoder strip
13
C4557-20007
Spring
Pinch spring - Provides tension on upper paper guide
15
C6426-40103
Gear
Kicker bar cam gear - Gear with cam lobe and offset pin
16
C6426-40118
Kicker
Kicker bar - Restacks paper in paper input tray stack after the top sheet is picked
18
C6426-00017
Spring
Lifter spring - Provides upper tension on the kicker bar (cam follower) lift plate
19
C6426-40098
Guide
Lower paper guide housing (Does NOT include any attaching parts)
20
C6429-60141
Guide
Inner paper guide (Includes antistatic brush) - Guides the paper through the print mech and over the upper paper guide
21
C4557-00009
Spring
Separator spring - Provides pressure between separator assembly and the center drive roller
22
C6426-00003
Bracket
IEC connector bracket - Holds the power cord socket
23
C6426-40102
Peg
Separator Peg - Pushes up the separator pad during the paper pick operation
24
C4557-40015
Roller
Rear roller (Black) - Between paper and rear paper guide
25
C4557-20003
Spring
Rear roller spring - Flexible axle for rear roller
26
C6426-00004
Support
Upper paper guide support - Support bracket which attaches to the print mech frame for mounting the upper paper guide
|
|