Part |
Description |
|
Other_Parts - Multifunction finisher |
|
Accumulator - Accumulator assembly - Holds paper until print job finish then moves to stapler or correct output bin |
|
Drive_Assembly - Process cartridge drive assembly - Includes all eight developing and drum motors |
|
Power_Supply - Power Supply Assembly - For 200VAC to 240VAC operation |
|
Accumulator - Accumulator assembly - Holds paper until print job finish then moves to stapler or correct output bin |
|
Power_Supply - Power Supply Assembly - For 100VAC to 127VAC operation |
|
Drive_Assembly - Process cartridge drive assembly - Includes all eight developing and drum motors |
|
Accumulator - Accumulator assembly |
|
Flipper - Paper flipper assembly - Mounts on top of the paper path router assembly - Flips sheet of paper from face-up to face-down to route to stacker properly |
|
Flipper - Paper flipper assembly - Mounts on top of the Paper Path Router assembly |
|
Power_Supply - Power Supply Assembly - For 100VAC to 127VAC operation |
|
Power_Supply - Power supply assembly - For 100VAC to 127VAC operation |
|
PC_Board - Stacker/stapler controller PC board - Mounts just above the power supply assembly |
|
PC_Board - Stacker/stapler controller PC board - Mounts just above the power supply assembly |
|
Stapler - Stacker/stapler controller PC board - Mounts just above the power supply assembly |
|
Stapler - Stapling unit - Stapler assembly for the stapler/stacker unit |
|
Fuser_Assembly - Fuser assembly - Bonds toner to paper with heat. FIXING ASSY. |
|
Power_Supply - Power Supply Assembly - For 100VAC to 127VAC operation |
|
Power_Supply - Power Supply Assembly - For 200VAC to 240VAC operation |
|
Deflector - Paper deflector - Guides paper out of dispose assembly - Snap-locks on little tangs on the back of the internal paper path cover |
|
Belt - Intermediate transfer belt assembly (ITB) |
|
Belt - Intermediate transfer belt assembly (ITB) |
|
Sheet - Controller PC board - For the 3,000-sheet stacker - Mounts just above the power supply assembly |
|
PC_Board - Formatter (main logic) board - For HP Color LaserJet 9500 series - Does not include memory,firmware, or EIO card. |
|
PC_Board - Formatter (main logic) board - For HP Color LaserJet 9500 series - Does not include memory,firmware, or EIO card. |
|
Tray - Tray 4 assembly (complete) - 2,000-sheet high capacity paper feeder assembly |
|
Tray - Tray 4 assembly (complete) - 2,000-sheet high capacity paper feeder assembly |
|
PC_Board - Controller pca for HP LaserJet 9000 Series |
|
Fuser_Assembly - Fuser assembly - Bonds toner to paper with heat - This part covers both 110VAC and 220VAC machines |
|
Carriage - Stapler carriage assembly - Carriage assembly that carries the stapler cartridge back and forth. |
|
Carriage - Carriage assembly |
|
Fuser_Assembly - Fuser assembly - Bonds toner to paper with heat - This part covers both 110VAC and 220VAC machines |
|
Flipper - Flipper (or paper reversing) assembly - First assembly the exiting paper from the printer goes through |
|
Flipper - Flipper (or paper reversing) assembly - First assembly the exiting paper from the printer goes through |
|
Drum - Yellow imaging drum assembly - Includes the photosensitive drum (or OPC), developing cylinder, and a small amount of toner (for priming) - Life expectancy is approximately 40,000 pages |
|
Drum - Magenta imaging drum assembly - Includes the photosensitive drum (or OPC), developing cylinder, and a small amount of toner (for priming) - Life expectancy is approximately 40,000 pages |
|
Drum - Cyan imaging drum assembly - Includes the photosensitive drum (or OPC), developing cylinder, and a small amount of toner (for priming) - Life expectancy is approximately 40,000 pages |
|
Power_Supply - High voltage power supply assembly - Mounts on the upper rear of print engine frame |
|
Power_Supply - High voltage power supply assembly - Mounts on the upper rear of print engine frame |
|
PC_Board - DC controller PC board - Controls the timing and functionality of the multifunction finisher - Mounts on the rear frame above the power supply |
|
Tray - 2,000-sheet paper cassette tray (Tray 4) - Part number is for the paper tray ONLY |
|
Cable - Video board cable - Cable between main power supply and video controller PC Board |
|
Cable - Video board cable - Cable between main power supply and video controller PC Board |
|
PC_Board - Controller PC board for the 3,000-sheet stacker - Mounts just above the power supply assembly |
|
Deflector - Paper deflector - Guides paper out of dispose assembly - Snap-locks on little tangs on the back of the internal paper path cover |
|
Power_Supply - Stapler power supply |
|
Drive_Assembly - Toner cartridge drive assembly - Print cartridge drive assembly - Includes toner cartridge sensors and drive motors M12 through M15 |
|
Pickup_Assembly - Paper pickup assembly - Includes both pickup motors - No lower level parts available for this assembly |
|
Module - Offset module for 3000 sheet stacker |
|
Module - Offset module for 3000 sheet stacker |
|
Power_Supply - Stapler power supply |
|
Power_Supply - 3000 sheet stacker power supply |
|
PC_Board - DC Controller board kit - Includes DC Controller board, video board cable and video flat cable |
|
Power_Supply - 3000 sheet stacker power supply |
|
Pickup_Assembly - Paper pickup assembly - Includes both pickup motors - No lower level parts available for this assembly |
|
Paper_Path_Module - Paper path router - Mounts underneath the Paper Flipper assembly |
|
PC_Board - DC Controller PCA |
|
Transfer_Assembly - Image Transfer Kit - Includes 2 small tray rollers, seven large tray rollers, one charcoal filter, one toner wipe, one transfer belt, and one transfer roller |
|
Laser_Scanner - Laser scanner assembly - Separate scanners used for each color tonner cartridge (four used) |
|
Laser_Scanner - Laser scanner assembly - Separate scanners used for each color tonner cartridge - Four used |
|
Memory - 256MB, 168-pin SDRAM DIMM memory module |
|
Paper_Path_Module - Paper path router - Mounts underneath the paper flipper assembly - Routes paper to the correct bin after leaving the flipper assembly |
|
Memory - 128MB, 100-pin SDRAM DIMM memory module |
|
Drive_Assembly - Toner cartridge drive assembly - Print cartridge drive assembly - Includes toner cartridge sensors and drive motors M12 through M15 |
|
Stapler - Stapler unit for 3000 sheet stapler/stacker |
|
Drum - Black imaging drum assembly - Includes the photosensitive drum (or OPC), developing cylinder, and a small amount of toner (for priming) - Life expectancy is approximately 40,000 pages |
|
Memory - 128MB, 168-pin SDRAM DIMM memory module |
|
Power_Supply - Low voltage power supply - Includes AC input power cord |
|
Stapler - Stapler unit for 3000 sheet stapler/stacker |
|
Drive_Assembly - Fuser drive assembly - Includes the two support plates, drive gears, and 24VDC motor (M10) |
|
Other_Parts - See c8088-69536 |
|
Hard_Drive - Replacement for part J6054B 10GB minimum, 20GB maximum EIO hard disk - Can be installed in printers with EIO slots |
|
Hard_Drive - 40 GB EIO hard drive |
|
Pickup_Assembly - Manual feed pickup assembly - Tray 1 pickup assembly - Complete assembly |
|
Pickup_Assembly - Manual feed pickup assembly - Tray 1 pickup assembly - Complete assembly |
|
Panel - Display panel assembly - Control panel on front top of printer |
|
Drive_Assembly - Fuser drive assembly - Includes the two support plates, drive gears, and 24VDC motor (M10) |
|
Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
|
Memory - 32MB, 100-pin SDRAM DIMM memory module |
|
Paper_Path_Module - Vertical registration assembly |
|
Paper_Path_Module - Vertical registration assembly |
|
Power_Supply - High Voltage power supply assembly - Supplies high voltage power for the corona |
|
PC_Board - CRG Driver PC Board assembly - Print Cartridge Drive Controller PC Board |
|
PC_Board - Controller PC board - Tray 4 deck controller board - Controller PC Board - for 2000 sheet feeder - Uses data from volume and size PC boards to control paper tray |
|
Transfer_Assembly - Transfer assembly - Secondary transfer assembly - Transfer assembly at bottom of ITB assembly - T2 transfer assembly |
|
PC_Board - CRG Driver PC Board assembly - Print Cartridge Drive Controller PC Board |
|
Feeder - Paper Input Unit (PIU)Paper pick-up assembly - For paper input tray 4 |
|
PC_Board - Controller PC board |
|
PC_Board - Process cartridge PC Board - Image drum PC Board |
|
Power_Supply - High Voltage power supply assembly - Supplies high voltage power for the corona |
|
Roller - Paper registration roller assembly - Complete assembly |
|
Roller - Paper registration roller assembly - Complete assembly |
|
Transfer_Assembly - Secondary Transfer assembly - Complete assembly - Transfer roller assembly at bottom of ITB assembly - T2 |
|
Cover - Delivery cover assembly - Lower left door assembly - With face-up output roller and flapper/diverter |
|
Cover - Left front cover assembly |
|
Memory - 128MB, 168-pin SDRAM DIMM memory module |
|
Sensor - Optical sensor kit - Contains the optical sensors that sense the location of the stacking tray/top of paper stack. |
|
Duplexer - Duplexer assembly kit - Required for two-sided printing - Includes the duplexer assembly and installation instructions (multi-lingual) |
|
Sensor - Optical sensor kit - Contains the optical sensors that sense the location of the stacking tray/top of paper stack. |
|
Tray - 500 Sheet paper cassette - Paper cassette used for Tray 2 and Tray 3 |
|
Bin - Booklet bin - Output tray that holds stapled and folded booklets |
|
Memory - 8MB Traditional Chinese font MROM DIMM - For LaserJet printers |
|
PC_Board - Memory switch PC board assembly - Mounts on the rear of the toner cartridge drive assembly |
|
Cable - Jet-link cable and power cord assembly |
|
Panel - Display panel assembly - Control panel on front top of printer |
|
Memory - 8MB Simplified Chinese font MROM DIMM - For LaserJet printers |
|
Fan - Cooling fan - Fan FM3 - This fan is the right side fan of two fans located on upper right side of printer - Upper right fan |
|
Cleaner - Intermediate Transfer Belt (ITB) cleaner assembly - Moves excess toner from ITB to catch tray assembly - Small blue handle to left of large green one |
|
Print_Server - JetDirect 620n internal print server - 10BaseT and 100BaseTX LAN interface board - Plugs into peripheral EIO slot - Has an RJ-45 connector |
|
Print_Server - JetDirect 620n internal print server - 10BaseT and 100BaseTX LAN interface board - Plugs into peripheral EIO slot - Has an RJ-45 connector |
|
Print_Server - JetDirect 620n internal print server - 10BaseT and 100BaseTX LAN interface board - Plugs into peripheral EIO slot - Has an RJ-45 connector |
|
Print_Server - JetDirect 620N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
|
Cover - Rear cover assembly - Rear cover of printer with air filters |
|
Cover - Rear cover of 3000 sheet output device |
|
Sensor - Registration sensor assembly - Located in front of ITB assembly behind right side door |
|
Print_Server - JetDirect 615N internal print server LAN interface board - 10Base-T and 100Base-TX - Plugs into peripheral EIO slot, has RJ-45 connector. |
|
Feeder - Delivery feed assembly - Moves paper to output tray after Fuser Assembly on left side of printer |
|
Caster - Swivel caster with height adjustable starwheel |
|
Bin - Stacker output bin - Job stacker and upper output tray for the multifunction finisher assembly |
|
Door - Front door assembly - Right side |
|
Cover - Stapler controller PC board cover - Includes label |
|
Memory - 64MB SDRAM DIMM memory module |
|
Feeder - Delivery feed assembly - Moves paper to output tray after Fuser Assembly on left side of printer |
|
Door - Print image drum door - Door on front that covers all four print image drum cartridges |
|
Cleaner - Intermediate Transfer Belt (ITB) cleaner assembly - Moves excess toner from ITB to catch tray assembly - Small blue handle to left of large green one |
|
Door - Front door assembly - Right side |
|
Door - Front door assembly - Left side |
|
Feeder - Face down delivery feed assembly - Feeds paper to face-down/top output tray |
|
Feeder - Face down delivery feed assembly - Feeds paper to face-down/top output tray |
|
Cover - Front cover of 3000 sheet stacker |
|
Cable - Laser cable - Cable between each of the four laser/scanner assemblies and the DC controller PCA |
|
Sensor - Registration sensor assembly - Located in front of ITB assembly behind right side door |
|
Cover - Rear cover assembly - Includes the rear cover shell with support leg cover |
|
Memory - Color LaserJet 9500 firmware DIMM - Revision V05.007.1 |
|
Door - Stapler/stacker access door |
|
Cable - Jet link interface cable assembly - Includes the coiled cable with the printer interface connector on one end and PC board connector on the other |
|
Cover - Top cover - Left side top cover - Display panel assembly attaches to this cover |
|
Caster - Swivel caster with height adjustable starwheel |
|
Memory - 16MB, 100-pin SDRAM DIMM memory module |
|
Motor - Registration motor - Drives registration roller assembly - 24VDC - Motor M11 |
|
Latch - Latching mechanism - Attaches to left side of printer to secure stacker/stapler to printer |
|
Stapler - Stapler/STKR PKG Kit |
|
PC_Board - Memory switch PC board assembly - Mounts on the rear of the toner cartridge drive assembly |
|
Motor - Deck drive motor (M303) only - Mounts in the 2,000-sheet paper feeder assembly |
|
Motor - Deck drive motor (M303) only - Mounts in the 2,000-sheet paper feeder assembly |
|
Motor - Registration motor - Drives registration roller assembly - 24VDC - Motor M11 |
|
Door - Door assembly - Right side lower door assembly - Right side rear hinged door below upper ITB access door |
|
Roller - Transfer roller assembly |
|
Connector - Connector pcb assy |
|
Roller - Transfer roller - Primary transfer roller assembly |
|
Cartridge - Staple cartridge - Contains 5000 staples - For the add-on staple/stacker unit |
|
Bin - Stacker output bin - Job stacker and upper output tray for the multifunction finisher assembly |
|
Cover - Rear cover assembly - Rear cover of printer with air filters |
|
Cleaner - Image Cleaning Kit - Includes one air filter, one transfer cleaner (cleaning blade), one toner collection bottle |
|
Bottle - Waste toner collection bottle assembly |
|
Door - Door assembly - Right side lower door assembly - Right side rear hinged door below upper ITB access door |
|
Drive_Assembly - 2000-sheet feeder drive assembly |
|
Drive_Assembly - 2000-sheet feeder drive assembly |
|
Cover - Top cover - Left side top cover - Display panel assembly attaches to this cover |
|
Cable - Rear lower cable - Main lower cable from the DC controller board |
|
Cartridge - Replacement staple cartridge assembly - Holds 5000 staples - For the Multifunction finisher assembly |
|
Paper_Path_Module - Paper path connection assembly - Directs paper from the high capacity input assembly output to the vertical input path on the print engine |
|
Paper_Path_Module - Paper path connection assembly - Directs paper from the high capacity input assembly output to the vertical input path on the print engine |
|
Drive_Assembly - Registration drive assembly - Gearbox assembly for registration roller assembly |
|
Bottle - Waste toner collection bottle assembly |
|
Door - Front door assembly - Left side |
|
Cover - Foot cover for HP Color LaserJet 9500 Series |
|
Cover - Rear cover assy |
|
Fan - Cooling fan - Fan that cools the fuser assembly and print cartridge area - FM4 |
|
Cable - Fuser connecting cable assembly - Cable with large black main connector for Fuser Assembly |
|
Sensor - Waste toner sensor assembly - Mounts to the front of the print engine frame assembly |
|
Cable - Fuser connecting cable assembly - Cable with large black main connector for Fuser Assembly |
|
Cover - Front cover for the 2,000-sheet paper feeder assembly |
|
PC_Board - Paper size PC board |
|
Cover - Rear center cover for the 2,000-sheet paper feeder assembly |
|
Caster - Front swivel caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Connector - Pedestal connector assembly - Contains both power connectors located on both sides at rear of pedestal and Pedestal Controller PC board |
|
Cover - Top cover - Right side top cover |
|
Tensioner - Latch tensioner assembly - Provides tension for image cartridge latch - Four used |
|
Cover - Foot cover - Plastic panel that covers the bottom support arms and casters |
|
Cover - Stacker controller PC board cover - Includes label |
|
Cover - Left cover for the 2,000-sheet paper feeder assembly |
|
Cover - Front cover assembly - Includes the front cover panel with support leg cover and the stapler access door assembly |
|
PC_Board - Connector PC Board - High voltage connector PC Board |
|
Sensor - Humidity sensor assembly - Located between the two fans on upper right side of printer |
|
Rod - Attachment rod assembly - Includes the mounting bracket, attachment rod and the slide on plastic latch - Aligns the stacker or multifunction finisher to the printer |
|
Cable - Laser cable - Cable between each of the four laser/scanner assemblies and the DC controller PCA |
|
Motor - Fuser drive motor - Drives fuser rollers, delivery roller and ITB cleaner - 24VDC |
|
Motor - Fuser drive motor - Drives fuser rollers, delivery roller and ITB cleaner - 24VDC |
|
Link - Rear link unit - Small plate with three gears and a spring loaded arm - Mounts in the interior upper rear of the print engine frame assembly |
|
Fan - Cooling fan - Fan that cools the delivery unit and scanner area - FM2 |
|
Fan - Cooling fan - Fan that cools the delivery unit and scanner area - FM2 |
|
Lever - Lever assembly - |
|
Cover - Right cover for the 2,000-sheet paper feeder assembly |
|
Sensor - Paper size sensing assembly |
|
Sensor - Paper size sensing assembly |
|
Tray - Face up paper output tray |
|
Fan - Cooling fan - Delivery cover assembly fan - Two used, FM6 and FM1 |
|
Fan - Cooling fan - Fan FM7 - This fan is the left side fan of two fans located on upper right side of printer - Ozone fan |
|
Hardware - Screw kit - Includes all screws used on Stapler/Stacker and 3000 Sheet Stacker |
|
Holder - Cable holder assy |
|
Drive_Assembly - Registration drive assembly - Gearbox assembly for registration roller assembly |
|
Cover - Rear cover assembly - Rear plastic pedestal cover with input side cover |
|
Cover - Bubbled cover - Half-domed shaped cover - Covers the inlet for the power cord and interface cable |
|
PC_Board - Paper size PC board |
|
Shaft - Soft link shaft assembly - Silver shaft and plastic cams that lift ITB cleaning blade into position |
|
Fan - Cooling fan - Fan FM7 - This fan is the left side fan of two fans located on upper right side of printer - Ozone fan |
|
Guide - Guide Bar Kit - Grey plastic piece with four curved fingers to guide paper - Kit includes accumulator, two screws and instructions |
|
Sensor - Humidity sensor assembly - Located between the two fans on upper right side of printer |
|
PC_Board - Regulator PC Board - Interlock power supply - Provides 24VDC to interlocks |
|
Cable - Flipper and paper path ribbon cable |
|
Cleaner - Front cleaner support - Metal support for ITB cleaner assembly on front of printer |
|
Cover - Lower right front corner cover for tray 2 and 3 |
|
Guide - Rear guide rail - Guide rail for right side of ITB assembly |
|
Cover - Top right cover - Cover on right side above Tray 1 |
|
Caster - Front swivel caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Caster - Stationary caster - Non-adjustable caster - Mounts on the bottom front right of the multifunction finisher |
|
Filter - Ozone filter - Charcoal air filter on right side upper cover |
|
Shaft - Soft link shaft assembly - Silver shaft and plastic cams that lift ITB cleaning blade into position |
|
Sensor - Door switch assembly - Includes the stapling door 'open' sensor microswitch assembly, two photosensors, sensor flags, and support structure |
|
Cover - Front cover for HP Color LaserJet 9500 Series |
|
Caster - Stationary rear caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Sensor - Paper volume sensing assembly |
|
Rod - Attachment rod assembly - Includes the mounting bracket, attachment rod and the slide on plastic latch - Aligns the stacker or multifunction finisher to the printer |
|
Door - Upper panel (or top door) assembly - Rectangular cover with molded-in hinge pins - Mounts on top of the multifunction finisher assembly |
|
Guide - Alignment Rod Guide kit - Blue plastic slider on alignment rod - Snaps into bottom of printer to locate alignment rod - Also includes metal ground contact piece between guide bar and printer chassis - Does not include rod |
|
Sensor - Waste toner sensor assembly - Mounts to the front of the print engine frame assembly |
|
Cable - Flat cable - Ribbon cable between DC Controller PCA and Print Driver PCA |
|
Caster - Stationary rear caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Connector - Pedestal connector assembly - Jetlink connector assembly between HCI (High Capacity Input) assembly and printer engine |
|
Sensor - Booklet bin 'full' sensor flag assembly - Semi triangular shaped arm with small rollers - Detects when the booklet bin has reached capacity |
|
Sensor - Delivery sensor assembly - Upper left paper output sensor assembly |
|
Cover - Cover - Right side rear corner of printer cover |
|
Cover - Rear center cover for the 2,000-sheet paper feeder assembly |
|
Caster - Stationary caster - Non-adjustable caster - Mounts on the bottom front right of the multifunction finisher |
|
Switch - Left interlock switch assembly - Left side door open switch |
|
PC_Board - Connector PC Board - High voltage connector PC Board |
|
Cover - Left rear cover assembly - Cover for left rear corner with power receptical opening |
|
Cover - Top cover for the 2,000-sheet paper feeder assembly |
|
Cover - Lower left cover - Smaller plastic piece below left door and diverter assembly |
|
Cover - Cover left for HP Color LaserJet 9500 Series |
|
Switch - Right interlock switch assembly - Right side door open switch |
|
Sensor - Paper volume sensing assembly |
|
Tensioner - Latch tensioner assembly - Provides tension for image cartridge latch - Four used |
|
Guide - Front rail guide - Guide for left side of ITB assembly when facing ITB |
|
Lever - Lever assy for HP Color LaserJet 9500 Series |
|
Switch - Switch assembly - Custom/standard paper switch |
|
Brush - Cleaning brush for HP Color LaserJet 9500 Series |
|
Torque_Limiter - Torque limiter for HP LaserJet 9040 9050 Series |
|
Cover - Right rear cover for the 2,000-sheet paper feeder assembly |
|
Caster - Caster for HP LaserJet 9000 Series |
|
Shaft - Photo-sensor (TLP1241) - Sensor flag activated. |
|
Sensor - Replacement for part WG8-5362-000CN ORDER WG8-5624-000CN PHOTO-INTERRUPTER TLP1241 Photo-sensor (TLP1241) - Sensor flag activated |
|
Switch - Interlock switch - Includes plastic holder and metallic activation flag - Senses when the multifunction finisher is not attached to printer |
|
Fan - Cooling fan - Fan FM3 - This fan is the right side fan of two fans located on upper right side of printer - Upper right fan |
|
Cable - Rear upper cable - Cable from DC Controller to many driver PC Boards |
|
Switch - Interlock switch - Includes plastic holder and metallic activation flag - Senses when the multifunction finisher is not attached to printer |
|
Connector - Jetlink connector - Connector between Tray 4 and printer engine |
|
Cover - Left rear cover for the 2,000-sheet paper feeder assembly |
|
Door - Stapler access door - Rectangular door at the top of the front cover assembly - Provids access to the stapler, folding jam knob, and product release handle |
|
PC_Board - Regulator PC Board - Interlock power supply - Provides 24VDC to interlocks |
|
Sensor - End paper sensor assembly - Contains Tray 2 and 3 paper length detection switches |
|
Filter - Air Filter - Pull out air filter on rear cover |
|
Power_Cord - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (For 240V in India) |
|
Power_Cord - Power cord (Flint Gray) - Has straight (F) C13 receptacle - 120V (USA, Mexico, and Canada) |
|
Shaft - Front lift lock assembly - Black plastic cam locks with a silver colored metal flat bar between that lift and lock front of ITB - Actuated via the large green handle on front of printer |
|
Sensor - End paper sensor assembly - Contains Tray 2 and 3 paper length detection switches |
|
Support - Front cleaner support - White plastic piece that attaches to metal support for ITB cleaner assembly on front of printer |
|
Cover - Internal paper path cover (dispose roller assembly cover) - Mounts under the upper panel (top door) toward the stacker bin |
|
Switch - Right interlock switch assembly - Right side door open switch |
|
Guide - Paper guide assembly before fuser - Rear portion of fuser entry paper guide assembly |
|
Rod - Rear lift lock assembly - Black plastic cam locks with a silver colored metal flat bar between that lift and lock rear of ITB - Actuated via the large green handle on front of printer. |
|
Sensor - Door switch assembly - Includes the stapling door 'open' sensor microswitch assembly, two photosensors, sensor flags, and support structure |
|
Cover - Lower left front corner cover for tray 2 and 3 - Includes power button |
|
Cover - Left upper cover assembly |
|
Switch - Switch assembly - Custom/standard paper switch |
|
Sensor - Booklet bin 'full' sensor flag assembly - Semi triangular shaped arm with small rollers - Detects when the booklet bin has reached capacity |
|
LED - User LED PC board - Small status indicator LED board - Mounts in the upper left corner of the front frame on the multifunction finisher assembly |
|
PC_Board - Paper volume sensor board |
|
Caster - Caster for HP LaserJet M9040 MFP |
|
Tray - Top tray - Moveable face-down paper output tray |
|
Cable - Right rear cable - 20 pin connector cable on right rear of Print Cartridge Driver Board |
|
Cover - Cover right for HP Color LaserJet 9500 Series |
|
Roller - Pickup roller - Tray 1 pickup roller |
|
Cover - Lower right cover - Small plastic piece below right door assembly |
|
Cover - Transfer roller assembly cover - Front cover of secondary transfer roller assembly |
|
LED - Service LED PC board - Small board with three LEDs - Used for troubleshooting jams and/or failures |
|
Lever - Toner cartridge release lever assembly - Four used |
|
Connector - Jetlink connector - Connector between Tray 4 and printer engine |
|
Link - Front link - Secondary transfer link arm - This is the one link that is not attached to the secondary tranfer assembly that moves with the big green handle |
|
Cable - Right rear cable - 20 pin connector cable on right rear of Print Cartridge Driver Board |
|
PC_Board - Paper volume sensor board |
|
PC_Board - Fuser sensor PC board - Mounts on a support bracket inside the print engine frame assembly |
|
Cable - Rear cable and holder assembly - Cable that runs from DC Controller board to both upper and lower paper length detection switches - Includes cover |
|
Link - Front link - Secondary transfer link arm - This is the one link that is not attached to the secondary tranfer assembly that moves with the big green handle |
|
Contact - High voltage contact holder assembly |
|
PC_Board - LED board - Small PC board with two LEDs and a connector - For indicating the operating status |
|
PC_Board - Fuser sensor PC board - Mounts on a support bracket inside the print engine frame assembly |
|
LED - User LED PC board - Small status indicator LED board - Mounts in the upper left corner of the front frame on the multifunction finisher assembly |
|
Power_Cord - Power cord (Flint Gray) - Has straight (F) C13 receptacle (for 120V in the United States, Mexico, and Canada) |
|
Shaft - Front lift lock assembly - Black plastic cam locks with a silver colored metal flat bar between that lift and lock front of ITB - Actuated via the large green handle on front of printer |
|
Guide - Fuser front guide assembly - Front portion of fuser paper entry guide - Part of guide with blue handle |
|
Spring - Tension spring - Provides tension for big green handle on front of printer |
|
Spring - Spring compression |
|
Connector - 20 pin connector - Connector between color registration array and Toner Driver PCA |
|
Support - MP Tray/Tray 1 rear support assembly - Tray 1 right side support |
|
Support - Door hinge support - Mounts on the upper right corner on the front of the print engine frame |
|
Support - Door hinge support - Mounts on the middle left of the front of the print engine frame |
|
Connector - Pin holder unit - Low voltage connector for the Intermediate Transfer Belt (ITB) assembly - Provides connection to the fan and thermistor inside the ITB assembly |
|
Support - Door hinge support - Mounts in the middle right on the front of the print engine frame |
|
Rod - Rear lift lock assembly - Black plastic cam locks with a silver colored metal flat bar between that lift and lock rear of ITB - Actuated via the large green handle on front of printer. |
|
Cable - Print Cartridge Drive cable - From Toner Driver PCA to Toner Cartridge motors and motor rotation sensors |
|
Antenna - Antenna holder assembly - Process cartridge sensor assembly - Four used |
|
Cable - Rear cable and holder assembly - Cable that runs from DC Controller board to both upper and lower paper length detection switches - Includes cover |
|
Spring - Compression spring - Provides tension for secondary transfer roller assembly front cover |
|
Cable - ITB sensor cable assembly - On left side of ITB assembly drawer |
|
Contact - High voltage contact holder assembly |
|
Connector - 10 pin connector - Connector between temperature/humidity sensor, ITB sensor, right door switch and Toner Driver PCA |
|
Caster - Stationary extended caster |
|
Connector - 5 pin connector - Connector between fan FM7 and Toner Driver PCA |
|
Label - Label-custom switch |
|
Lever - Toner cartridge release lever assembly - Four used |
|
Screw - Screw - M4 X 8mm long |
|
Support - Door hinge support - Mounts on the upper left corner on the front of the print engine frame |
|
Screw - Screw - M4 X 8mm long |
|
PC_Board - LED board - Small PC board with two LEDs and a connector - For indicating the operating status |
|
Lever - Paper size switching lever - To adjust paper size in tray (standard or custom size) |
|
Rod - Switch rod - Mechanical connection between power button and Low Voltage Power Supply PCA |
|
Cable - High voltage cable - Connects between the main power supply (J1) and the high voltage power supply (J201) |
|
Overlay - Control panel overlay - German |
|
Overlay - Control panel overlay - Netherlands |
|
Overlay - Control panel overlay - Norwegian |
|
Overlay - Control panel overlay - Polish |
|
Overlay - Control panel overlay - Czech |
|
Overlay - Control panel overlay - Traditional Chinese |
|
Power_Supply - Low voltage power supply - Includes AC input power cord |
|
Overlay - Control panel overlay - Finnish |
|
Overlay - Control panel overlay - Russian |
|
Overlay - Control panel overlay - Portuguese (Brazilian) |
|
Lever - Lever assembly - |
|
Overlay - Control panel overlay - Simplified Chinese |
|
Overlay - Control panel overlay - Italian |
|
PC_Board - Stacker/stapler controller PC board - Mounts just above the power supply assembly |
|
Overlay - Control panel overlay - Swedish |
|
Overlay - Control panel overlay - Japanese |
|
Overlay - Control panel overlay - Danish |
|
Overlay - Control panel overlay - Hungarian |
|
Power_Supply - Power Supply Assembly - For 200VAC to 240VAC operation |
|
Overlay - Control panel overlay - Castilian Spanish |
|
Cable - Print cartridge drive cable - From Toner Driver PCA to toner cartridge motors and motor rotation sensors |
|
LED - Service LED PC board - Small board with three LEDs - Used for troubleshooting jams and/or failures |
|
Cable - Fusing sensor cable assembly - Connects to Fuser sensor PC Board |
|
Cable - Fusing sensor cable assembly - Connects to Fuser sensor PC Board |
|
Guide - Paper guide assembly before fuser - Rear portion of fuser entry paper guide assembly |
|
Power_Cord - Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 120V in the USA, Canada, Mexico, Philippines, and Taiwan) |
|
Cable - Post controller cable - Connects between the high voltage power supply (J210) and the post charging unit (J501) |
|
Cover - Left front cover - Small vertical piece on left side of left cover assembly |
|
Guide - Cleaner guide - Guides for ITB cleaner blade - 2 used |
|
Guide - Paper guide wire-form - Large 'U' shaped paper guide that locks on the back of the paper flipper assembly |
|
Cover - Right front cover - Thin vertical plastic cover - Mounts on the right front of the printer |
|
Cable - Registration cable assembly - Includes 7P and 3P connectors |
|
Antenna - Antenna holder assembly - Process cartridge sensor assembly - Four used |
|
Tray - Waste toner catch tray - Slides beneath Intermediate Transfer Belt (ITB) cleaner assembly to collect waste toner |
|
Plate - Mounting plate - Metal guide on front of printer for assemblies that move during ITB (Intermediate Transfer Belt) cleaning cycle |
|
Support - MP Tray/Tray 1 rear support assembly - Tray 1 right side support |
|
Connector - Pin holder unit - Low voltage connector for the Intermediate Transfer Belt (ITB) assembly - Provides connection to the fan and thermistor inside the ITB assembly |
|
Roller - Feed separation pick-up roller - Rubber roller on a plastic collar with integrated gear and locking tab |
|
Cover - Transfer cable cover - Protects ITB and secondary transfer roller cables from ITB lift mechanism |
|
Mount - Door dampener hinge mount - Left side/fuser door dampener mount (two used) |
|
Overlay - Control panel overlay - Korean |
|
Power_Cord - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 220V in Europe, Saudi Arabia, South Africa, India, and Korea) |
|
Handle - Product release handle - Activates the product attachment latch at the top right of the unit |
|
Panel - Control panel - Insert on left side of control panel for 110V application |
|
Cable - Fusing motor cable - Cable between DC Controller PC Board and Fuser motor M10 |
|
Cable - Low voltage power supply cable - Connects between the power supply and the DC controller PC board |
|
Cable - Process cartridge cable - Connects between the print driver board (J608) and the high voltage board (J202) |
|
Cable - Crossmember cable - This cable connects J1701R, J3015D, J3013, and J3085 at rear of printer |
|
Cable - High voltage cable - Connects between the DC controller board (J101) and the high voltage power supply assembly (J203) |
|
Caster - Stationary extended caster |
|
Plate - Positioning plate - Attaches to metal support for ITB cleaner assembly on front of printer |
|
Pad - Guide pad - Small pads on each side of separation pad - Help guide paper to pickup roller |
|
Support - Door hinge support - Mounts on the upper right corner on the front of the print engine frame |
|
Support - Door hinge support - Mounts on the middle left of the front of the print engine frame |
|
Support - Door hinge support - Mounts on the upper left corner on the front of the print engine frame |
|
Support - Door hinge support - Mounts in the middle right on the front of the print engine frame |
|
Cable - Ribbon cable - Conntects between the toner controller board (J802) and the memory controller board (J1001) |
|
Gear - Handle mounting gear - Includes the 16 tooth gear and retaining 'E' clip - Manually driven by the green paper jam clearing handle for the fold assembly |
|
Strap - Door strap - Narrow plastic strap with a screw hole in one end |
|
Roller - Paper pick-up and feed roller assembly - Rubber roller with drive gear |
|
Cable - Rear lower cable - From DC Controller board to Secondary Transfer/Registration clutches and sensors - J121 to J3022, J3025, J3026 and J3027 |
|
Screw - Screw - M4 X 8mm long |
|
Link - Holder lift link - Black plastic fuser assembly lock link |
|
Spring - Compression spring |
|
Connector - 20 pin connector - Connector between color registration array and toner driver PCA |
|
Spring - Compression spring - Provides tension for secondary transfer roller assembly front cover |
|
Stopper - Stopper block letter 11x17 |
|
Stopper - Stopper block a4/a3 |
|
Cover - Rail cover - Fits over guide for left side of ITB assembly - protects ITB sensors |
|
Screw - Screw - 6 mm Phillips head screw with attached washer |
|
Spring - Tension spring - Provides tension for big green handle on front of printer |
|
Support - Side plate hinge support - Image drum door hinge |
|
Retainer - Link retainer - Retainer clip that holds secondary transfer assembly link arm in place |
|
Cable - ITB sensor cable assembly - On left side of ITB assembly drawer |
|
Connector - 10 pin connector - Connector between temperature/humidity sensor, ITB sensor, right door switch and Toner Driver PCA |
|
Connector - 5 pin connector - Connector between fan FM7 and toner driver PCA |
|
Overlay - Control panel overlay - European French |
|
Cable - Toner cartridge cable - Cable between Print Driver PCA and Toner Driver PCA |
|
Mount - Damper mounting block - Right side ITB door damper mounting bracket |
|
Ground - Grounding plate - Electrical ground plate on right side of ITB rear guide rail |
|
Overlay - Control panel overlay - English |
|
Accumulator - Accumulator assembly - Holds paper until print job finish then moves to stapler or correct output bin |
|
Care_Pack - HP Maintenance Kit Replacement Color LaserJet 9500/9500MFP fuser 110/220V service |
|
Care_Pack - HP Maintenance Kit Replacement Color LaserJet 9500/9500 MFP cleaning kit service |
|
Switch - Left interlock switch assembly - Left side door open switch |
|
Print_Server - JetDirect ew2400 802.11g wireless print server module - Includes power supply, USB cable, LAN/Ethernet cable, setup documentation and software |
|
Sensor - Delivery sensor assembly - Upper left paper output sensor assembly |
|
Care_Pack - HP 1 year Post Warranty Next business day Onsite Color LaserJet 9500 Hardware Support |
|
Connector - Connector (3-pin) - ORDER RG5-1928-000CN |
|
Care_Pack - HP 1 year Post Warranty 4 hour response 9x5 Onsite Color LaserJet 9500 Hardware Support |
|
Color_LaserJet - HP Color LaserJet 9500gp Printer |
|
PC_Board - Connector PC Board - High voltage connector PC Board |
|
Print_Server - JetDirect ew2400 802.11g wireless print server module |
|
Care_Pack - HP 2 year Post-Warranty Next business day onsite Color LaserJet 9500 Hardware Support |
|
Service_Guide_PH - HP Color LaserJet 9500gp Printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams. |
|
Fuser_Assembly - Fuser assembly - 110VAC/220VAC - Bonds toner to paper with heat |
|
Care_Pack - HP 1 year Post Warranty 4 hour response 13x5 Onsite Color LaserJet 9500 Hardware Support |
|
Care_Pack - HP Maintenance Kit Replacement Color LaserJet 9500/9500 MFP transfer service |
|
Care_Pack - HP 1 year Post Warranty Phone Assist Color LaserJet 3-9xxx/ScanJet N7xxx-9xxx Service |
