Part |
Description |
|
LaserJet - HP LaserJet 9000dn Printer |
|
Stacker_Assembly - Optional 3000 sheet stapler/stacker assembly - Stacks up to 3000 sheets of standard paper (20-lb bond) on the stapler bin, staples in multiple positions up to 50 sheets, and has job offset capabilities for easy handling |
|
Stacker_Assembly - Optional 3,000-sheet paper output stacker assembly - Stacks up to 3000 sheets of standard paper(20-lb bond) on the stacker bin, has job offset capabilities for easy handling, and job separation (first page offset) for shared environments |
|
Accumulator - Accumulator assembly - Holds paper until print job finish then moves to stapler or correct output bin |
|
Accumulator - Accumulator assembly - Holds paper until print job finish then moves to stapler or correct output bin |
|
Accumulator - Accumulator assembly |
|
Flipper - Paper flipper assembly - Mounts on top of the paper path router assembly - Flips sheet of paper from face-up to face-down to route to stacker properly |
|
Flipper - Paper flipper assembly - Mounts on top of the Paper Path Router assembly |
|
Fax_Module - Multi Functional Printer analog FAX accessory - Includes three language user manual, both parallel cables, phone cord, power module and power cord |
|
Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
|
Maintenance_Kit - Maintenance Kit (220V) - Replacement Parts after 350k Pages Includes, Fuser Assembly, 7 Feed/Separation Rollers, 2 Pickup Rollers and Transfer Roller |
|
Maintenance_Kit - Maintenance Kit - For 220 VAC - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer roller |
|
Maintenance_Kit - Maintenance Kit - For 120 VAC - Replacement Parts after 350k Pages Includes, Fuser Assembly, 7 Feed/Separation Rollers, 2 Pickup Rollers and Transfer roller |
|
Fuser_Assembly - Fuser Assembly - For 220 VAC to 240 VAC - Bonds toner to paper with heat |
|
Tray - Tray 4 assembly (complete) - 2,000-sheet high capacity paper feeder assembly |
|
Tray - Tray 4 assembly (complete) - 2,000-sheet high capacity paper feeder assembly |
|
Tray - Tray 4 assembly (complete) - 2,000-sheet high capacity paper feeder assembly |
|
Tray - 2,000-sheet high capacity paper feeder assembly |
|
Maintenance_Kit - Maintenance Kit (220V) - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer roller |
|
Maintenance_Kit - Maintenance Kit (220V) - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer roller |
|
Fuser_Assembly - Fuser Assembly - For 100 VAC to 127 VAC - Bonds toner to paper with heat |
|
Carriage - Stapler carriage assembly - Carriage assembly that carries the stapler cartridge back and forth |
|
Carriage - Stapler carriage assembly - Carriage assembly that carries the stapler cartridge back and forth. |
|
Carriage - Carriage assembly |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V Operation |
|
Maintenance_Kit - Maintenance Kit (120V) - Replacement parts after 350K pages includes, Fuser Assembly, seven Feed/Separation rollers, two Pickup rollers and Transfer roller assembly |
|
Maintenance_Kit - Maintenance Kit - For 120 VAC operation - Replacement parts after 350k pages - Includes fuser assembly, seven feed/separation rollers, two pick-up rollers and transfer roller |
|
Maintenance_Kit - Maintenance Kit (120V) - Replacement Parts after 350k Pages Includes, Fuser Assembly, 7 Feed/Separation Rollers, 2 Pickup Rollers and Transfer roller |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 220-240V operation |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 220-240V operation |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V Operation |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 220V to 240V operation |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 220-240V |
|
PC_Board - Formatter board - Main Logic PCA |
|
PC_Board - Formatter board - Main Logic PCA |
|
Power_Supply - Stapler power supply |
|
Maintenance_Kit - Maintenance Kit (220V) - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer roller |
|
Module - Offset module for 3000 sheet stacker |
|
Module - Offset module for 3000 sheet stacker |
|
Duplexer - Duplexer assembly - Enables double-sided printing by flipping the page over in the printing process |
|
Duplexer - Duplexer assembly - Enables double-sided printing by flipping the page over in the printing process |
|
Duplexer - Duplexer assembly - Enables double-sided printing by flipping the page over in the printing process |
|
Power_Supply - Stapler power supply |
|
Power_Supply - 3000 sheet stacker power supply |
|
Power_Supply - 3000 sheet stacker power supply |
|
Paper_Path_Module - Paper path router - Mounts underneath the Paper Flipper assembly |
|
Laser_Scanner - Laser/Scanner assembly - Mounts on the support structure in the print engine frame assembly |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V Operation |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V Operation |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V Operation |
|
Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V Operation |
|
Paper_Path_Module - Paper path router - Mounts underneath the paper flipper assembly - Routes paper to the correct bin after leaving the flipper assembly |
|
Power_Supply - Low voltage power supply - 110 VAC input |
|
Pickup_Assembly - Paper input unit - Entire assembly |
|
Laser_Scanner - Laser/Scanner assembly - Mounts on the support structue in the print engine frame assembly |
|
Fuser_Assembly - Fuser Assembly - For 100 VAC to 127 VAC - Bonds toner to paper with heat |
|
Fuser_Assembly - Fuser Assembly - For 100 VAC to 127 VAC - Bonds toner to paper with heat |
|
Stapler - Stapler unit for 3000 sheet stapler/stacker |
|
Pickup_Assembly - Paper pickup assembly |
|
Tray - Optional Tray 1 assembly - Complete Tray 1 assembly including rollers and mechanical drives |
|
Tray - Optional Tray 1 assembly - Complete Tray 1 assembly including rollers and mechanical drives |
|
Power_Supply - Low voltage power supply - 220V |
|
Stapler - Stapler unit for 3000 sheet stapler/stacker |
|
Hard_Drive - 10GB minimum, 20GB maximum EIO hard disk - Can be installed in printers with EIO slots - Provides mass storate capability for downloading fonts and macros - May also hold print jobs. |
|
Power_Supply - Low voltage power supply - 220V |
|
Registration - Registration roller assembly |
|
PC_Board - High voltage power supply board |
|
Power_Supply - High voltage power supply board |
|
Paper_Path_Module - Vertical registration assembly |
|
Paper_Path_Module - Vertical registration assembly |
|
Cartridge - HP Ultra-Precise print cartridge (Smart print cartridge) - Will print approximately 30,000 pages based on a 5% print density |
|
PC_Board - Controller PC board - Tray 4 deck controller board - Controller PC Board - for 2000 sheet feeder - Uses data from volume and size PC boards to control paper tray |
|
PC_Board - Controller PC board - Tray 4 deck controller board - Controller PC Board - for 2000 sheet feeder - Uses data from volume and size PC boards to control paper tray |
|
Feeder - Paper Input Unit (PIU)Paper pick-up assembly - For paper input tray 4 |
|
Paper_Input_Unit - Paper Input Unit (PIU) - For paper input tray 4. |
|
PC_Board - Controller PC board |
|
Control_Panel - Control panel assembly - Control buttons and display Control Panel Assembly |
|
Control_Panel - Control panel - Control panel assembly - Control buttons and display Control Panel Assembly |
|
Power_Supply - High voltage power supply board - Mounts on the upper rear of the printer |
|
PC_Board - DC controller board assembly |
|
Control_Panel - Control Panel Assembly |
|
Control_Panel - Control Panel Assembly |
|
Cover - Right cover assembly - Includes all components attached to this door |
|
Delivery - Delivery assembly - Includes the curved plastic structure, various rollers and gears, and the 'L' shaped metal support structure with three fans |
|
Delivery - Delivery assembly - Includes the curved plastic structure, various rollers and gears, and the 'L' shaped metal support structure with three fans |
|
Delivery - Delivery assembly - Includes the curved plastic structure, various rollers and gears, and the 'L' shaped metal support structure with three fans |
|
Door - Left door and diverter assembly |
|
Door - Left door assembly |
|
Cover - Right cover assembly - Includes all components attached to this door |
|
Drive_Assembly - Drum feed drive assembly |
|
Drive_Assembly - Drum feed drive assembly |
|
PC_Board - LED PCA - Control panel LED display |
|
Power_Supply - Power supply assembly |
|
Cartridge - 43x hi yield black toner |
|
Power_Supply - Power supply assembly |
|
Tray - 500-sheet paper input tray assembly |
|
Delivery - Delivery cross member assembly - Includes the 'L' shaped support bracket with the rear delivery fan (Fan 3), front delivery fan (Fan 4), and face down tray fan (Fan 6) |
|
Delivery - Delivery cross member assembly - Includes the 'L' shaped support bracket with the rear delivery fan (Fan 3), front delivery fan (Fan 4), and face down tray fan (Fan 6) |
|
Drive_Assembly - Fuser delivery drive assembly - Includes gears, motor and microswitch for fuser drive - Also drives delivery roller |
|
Cable - Jet-link cable and power cord assembly |
|
Drive_Assembly - Fuser delivery drive assembly - Includes gears, motor and microswitch for fuser drive - Also drives delivery roller |
|
Power_Supply - High Voltage power supply board - Mounts on the upper rear of the printer |
|
PC_Board - DC controller board assembly |
|
Motor - Drum feed drive motor |
|
Hard_Drive - 5GB EIO hard drive |
|
Memory - 133 MHz 128MB, 100-pin SDRAM DIMM memory module Synchronous DRAM DIMM |
|
Memory - 128MB, 100-pin SDRAM DIMM memory module |
|
Cover - Rear cover of 3000 sheet output device |
|
PC_Board - Memory controller PC Board |
|
Delivery - Face-up delivery assembly |
|
Delivery - Face-up delivery assembly |
|
Memory - 64MB SDRAM - 100MHz synchronous DRAM - DIMM package |
|
Motor - Drum feed drive motor |
|
PC_Board - Paper pickup board |
|
Memory - 32MB, 100-pin SDRAM DIMM memory module |
|
Memory - 32MB, 100-pin SDRAM DIMM memory module |
|
Caster - Swivel caster with height adjustable starwheel |
|
Cover - Stapler controller PC board cover - Includes label |
|
PC_Board - Memory controller PC Board - Toner cartridge |
|
Cover - Front cover assembly - Large door above trays 2 and 3 |
|
Motor - Fuser delivery motor - 24VDC |
|
Lifter - Cartridge lifter assembly |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin high density IEEE 1284C (M) connector (type C) - 10m (33ft) long |
|
Cable - Interface cable kit - For HP peripherals designed for use in an AppleTalk/Phonenet network - Not for Macintosh models that have recessed I/O connectors |
|
Cover - Front cover of 3000 sheet stacker |
|
Memory - 16MB, 100-pin SDRAM DIMM memory module |
|
Bin - Stapler bin - Lower tray that holds stapled print jobs |
|
Door - Stapler/stacker access door |
|
Caster - Swivel caster with height adjustable starwheel |
|
Bin - Face up bin - Top paper tray |
|
Fan - Controller board tubeaxial fan |
|
Motor - Deck drive motor (M303) only - Mounts in the 2,000-sheet paper feeder assembly |
|
PC_Board - LED PCA - Control panel LED display |
|
Cover - Front cover assembly - Large door above trays 2 and 3 |
|
Cover - Top left cover - Face down paper output cover - Located on the left side portion of the top cover |
|
Cartridge - Replacement staple cartridge - Contains 5000 staples |
|
Cartridge - Replacement staple cartridge assembly - Holds 5000 staples |
|
Drive_Assembly - Feed drive assembly - Includes the drive motor (M303), support bracket, and the four drive gears - Mounts in the 2,000-sheet paper feeder assembly |
|
Drive_Assembly - 2000-sheet feeder drive assembly |
|
Drive_Assembly - 2000-sheet feeder drive assembly |
|
Transfer_Assembly - Transfer roller assembly - Includes both transfer guides and transfer roller |
|
Wing - Wing kit - Output accumulator wing replacement |
|
Fan - Tubeaxial fan for HP LaserJet 9000 Series |
|
Fan - Tubeaxial fan for HP LaserJet M9040 MFP |
|
Transfer_Assembly - Transfer roller assembly - Includes transfer guides and transfer roller |
|
Fan - Tubeaxial fan for HP LaserJet 9040 9050 Series |
|
Cable - 8120-8724 IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin high density IEEE-1284C (M) connector (type C) - 3.0m (9.8ft) long mini connector. |
|
Caster - Stationary caster - Fixed position caster |
|
Paper_Path_Module - Paper path connection assembly - Directs paper from the high capacity input assembly output to the vertical input path on the print engine |
|
Paper_Path_Module - Paper path connection assembly - Directs paper from the high capacity input assembly output to the vertical input path on the print engine |
|
Holder - Fuser connector holder assembly |
|
Lifter - Cartridge lifter assembly |
|
Roller - Transfer roller - Includes the long black spongy roller, roller shaft, and drive gear - Transfers static charge to the paper |
|
Cover - Foot cover for HP Color LaserJet 9500 Series |
|
Cover - Rear cover assembly |
|
Guide - Transfer guide assembly (Ribbed plastic piece) - Has slot for the transfer roller assembly |
|
Guide - Transfer guide assembly (Ribbed plastic piece) - Has slot for the transfer roller assembly |
|
Cable - Main cable harness and holder assembly |
|
Cover - Front cover for the 2,000-sheet paper feeder assembly |
|
Cable - Main cable harness and holder assembly |
|
PC_Board - Paper size PC board |
|
Cover - Rear center cover for the 2,000-sheet paper feeder assembly |
|
Overlay - Control panel overlay - For 220V application |
|
Bin - Stacker bin - Face down lower accumulator tray |
|
PC_Board - Paper pickup board |
|
Cover - Top right cover - Located on the right side portion of the top cover |
|
Caster - Front swivel caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Holder - Fuser connector holder assembly |
|
Cable - Cable assembly for HP LaserJet 9000 Series |
|
Interlock - Interlock switch - Senses when stacker/stapler is correctly attached to printer |
|
Cover - Stacker controller PC board cover - Includes label |
|
Cover - Left cover for the 2,000-sheet paper feeder assembly |
|
Receptacle - A/C power input receptacle module and power switch |
|
Fan - Tubeaxial fan (fan 1) - Provides air to the power supply |
|
Fan - Tubeaxial fan for HP LaserJet 9000 Series |
|
Receptacle - A/C power input receptacle module and power switch |
|
Door - Stacker door assembly with label |
|
Cable - Cable assembly - Fuser power cable |
|
Cover - Front inside cover - Cover behind front drop down cover |
|
Cover - Right cover for the 2,000-sheet paper feeder assembly |
|
Sensor - Paper size sensing assembly |
|
Sensor - Paper size sensing assembly |
|
Tray - Face up paper output tray |
|
Cover - Service cover assembly - Cover for pickup and separation rollers |
|
Holder - Transfer roller holder assembly - Includes the base structure, latch, anti-static brush, pressure springs, bushings, and contact springs - Assembly that the transfer roller mounts in |
|
Hardware - Screw kit - Includes all screws used on Stapler/Stacker and 3000 Sheet Stacker |
|
Latch - Right cover latch handle assembly |
|
Fan - Tubeaxial fan for HP LaserJet 9000 Series |
|
Fan - Tubeaxial fan for HP LaserJet 9000 Series |
|
Cover - Bubbled cover - Half-domed shaped cover - Covers the inlet for the power cord and interface cable |
|
Guide - Transfer roller guide - Mounts to the top of the base structure of the transfer roller assembly |
|
PC_Board - Paper size PC board |
|
Lever - Cartridge release lever assembly |
|
Cable - Flipper and paper path ribbon cable |
|
Knob - Fuser jam removal knob |
|
Cover - Lower right front corner cover for tray 2 and 3 |
|
Fan - Tubeaxial fan (fan 4) - Mounts on the upper left crossmember on the delivery assembly |
|
Caster - Front swivel caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Plastics_Kit - "Stapler plastic parts kit - Includes cable holders, stapler door hinges and safety switch cover" |
|
Cover - Left upper cover - Small cover above left door |
|
Cover - Left upper cover - Small cover above left door |
|
Caster - Stationary rear caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Sensor - Paper volume sensing assembly |
|
Cover - Right rear cover - small cover strip on rear side of right cover assembly |
|
Rail - Right rail assembly |
|
Cable - Fuser Assembly high voltage cable and connectors |
|
Caster - Stationary rear caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used) |
|
Knob - Fuser jam removal knob |
|
Latch - Right cover latch handle assembly |
|
Cover - Rear center cover for the 2,000-sheet paper feeder assembly |
|
Holder - Transfer roller holder assembly - Includes the base structure, latch, anti-static brush, pressure springs, bushings, and contact springs - Assembly that the transfer roller mounts in |
|
Switch - Safety switch assembly - Stapler door safety lock-out switch |
|
Rail - Left upper rail assembly |
|
Cover - Top cover for the 2,000-sheet paper feeder assembly |
|
Cover - Lower left cover - Smaller plastic piece below left door and diverter assembly |
|
Latch - Latch mount assembly |
|
Rail - Right rail assembly |
|
Sensor - Paper volume sensing assembly |
|
Clip - Paper stopper clip kit - Both clips that mount below the wings on paper output accumulator |
|
Switch - Switch assembly - Custom/standard paper switch |
|
Cable - Jetlink connector socket and cable |
|
Torque_Limiter - Torque limiter for HP LaserJet 9040 9050 Series |
|
Cover - Right rear cover for the 2,000-sheet paper feeder assembly |
|
Damper - Left door damper assembly |
|
Caster - Caster for HP LaserJet 9000 Series |
|
Cover - Left upper cover - Small piece above left door |
|
Plastics_Kit - Stacker plastic kit - Includes cable holders, stapler door hinges, and safety switch cover |
|
Contact - Toner cartridge contact assembly |
|
Connector - Jetlink connector - Connector between Tray 4 and printer engine |
|
Cable - Cable assembly for HP LaserJet 9040 9050 Series |
|
Lever - Cartridge release lever assembly |
|
Cover - Left rear cover for the 2,000-sheet paper feeder assembly |
|
Rail - Left lower rail assembly |
|
Strap - Restraining strap |
|
Sensor - End paper sensor assembly - Contains Tray 2 and 3 paper length detection switches |
|
Roller - Separation roller - For tray 1 assembly |
|
Contact - Toner cartridge contact assembly |
|
Cover - Tray 1 blanking cover |
|
Sensor - End paper sensor assembly - Contains Tray 2 and 3 paper length detection switches |
|
Rail - Left upper rail assembly |
|
Cable - Jetlink connector socket and cable |
|
PC_Board - Delivery assembly PC board |
|
Cable - Fan control cable - Includes cable and holder - On back of printer routes cable around DC controller PC board |
|
Cover - Lower left front corner cover for tray 2 and 3 - Includes power button |
|
Switch - Switch assembly - Custom/standard paper switch |
|
PC_Board - Paper volume sensor board |
|
Switch - Black toner cartridge switch - Detects when black cartridge is in correct position |
|
Overlay - Control panel overlay - For 110V application |
|
Damper - Left door damper assembly |
|
Cover - Lower right cover - Small plastic piece below right door assembly |
|
Link - Connector link - Door ajar flag |
|
Guide - Output guide - Paper input unit output guide |
|
Connector - Jetlink connector - Connector between Tray 4 and printer engine |
|
Rail - Cartridge guide rail - Right side toner cartridge guide rail |
|
Rail - Left lower rail assembly |
|
Cable - Fuser Assembly high voltage cable and connectors |
|
PC_Board - Paper volume sensor board |
|
Latch - Latch mount assembly |
|
Mount - Front pressure mount for toner cartridge |
|
PC_Board - LED board - Small PC board with two LEDs and a connector - For indicating the operating status |
|
Roller - Pick-up roller for optional tray 1 |
|
Cable - Multi-purpose/tray 1 cable assembly |
|
Clip - E-ring retainer clip |
|
Fuse - Fuse - 3.15A, 250V max |
|
Mount - Rear Fuser Assembly mount |
|
Screw - Screw - M4 X 8mm long |
|
Cover - Fan cover - Metal cover for fan #5 - Cartridge fan cover |
|
PC_Board - Delivery assembly PC board |
|
Mount - Front Fuser Assembly mount |
|
Clip - Retaining E-ring |
|
Retainer - Push nut retainer |
|
Screw - Screw with captured washer - To hole plastic to metal - M4X6 |
|
Screw - TP Screw - Pan/washer head machine screw - M3X6 |
|
Cable - Cable assembly for HP LaserJet 9000 Series |
|
Lever - Custom/standard media size selection switch lever - Mounts on the left side of the 500-sheet paper input tray |
|
PC_Board - LED board - Small PC board with two LEDs and a connector - For indicating the operating status |
|
Screw - Screw with captured washer - Used to fasten plastic to metal - M4 X 6mm screw |
|
Screw - TP Screw - Pan/washer head machine screw - M3X8 |
|
Lever - Paper size switching lever - To adjust paper size in tray (standard or custom size) |
|
Cable - Cable assembly for HP LaserJet 9040 9050 Series |
|
Switch - Fuser delivery drive assembly microswitch |
|
Handle - Registration guide handle |
|
Rail - Right rail guide |
|
PC_Board - 3000 sheet stacker controller PC Board |
|
Rail - Left rail guide |
|
Cable - RS-422 serial cable - 8-pin (M) to 8-pin (M) - 2.0m (6.6ft) long |
|
Rod - ON/OFF switch push rod |
|
Latch - Front cover latch - Roller latch that holds front cover |
|
Rail - Front Fusing Rail |
|
Cable - Fan connecting cable - For both Fan 1 and 2 |
|
Rail - Rear Fusing Rail |
|
Guide - Cartridge guide - Plastic structure with cartridge guide slot molded into it - Mounts on the upper front side of the registration assembly |
|
Mount - Rear pressure mount for toner cartridge |
|
Housing - Jetlink connector housing and cable holder assembly |
|
Roller - Feed separation pick-up roller - Rubber roller on a plastic collar with integrated gear and locking tab |
|
Shutter - Laser shutter - Cartridge shutter actuator - Piece that opens cartridge shutter as it is inserted into the printer |
|
Hinge - Front cover hinge |
|
Mount - Door dampener hinge mount - Left side/fuser door dampener mount (two used) |
|
Cover - Fan cover - Metal cover for fan #5 - Cartridge fan cover |
|
Foot - Chassis foot - Support for right side of printer chassis - Two used |
|
Guide - Paper pickup guide - Plastic shaft with several fins on it - Mounts on the upper right side of the print engine frame assembly |
|
Cleaner - Toner cleaning cloth - Specially treated cloth for absorbing toner (1 per package) - Ideal for cleaning up toner spills |
|
Cable - Cable assembly for HP LaserJet 9000 Series |
|
Contact - Fuser electrical contact leaf spring |
|
Cover - Tray 1/MP Tray cable cover |
|
Cover - Right front inside corner cover |
|
Hinge - Cover hinge - Half of hinge that attaches to front cover |
|
Roller - Paper pick-up and feed roller assembly - Rubber roller with drive gear |
|
Foot - Chassis foot - Support for left side of printer chassis - Two used |
|
Mount - Front Fuser Assembly mount |
|
Spring - Tension spring for HP LaserJet M9040 MFP |
|
Knob - Jam removal knob |
|
Screw - Machine screw with attached washer - M3, 10mm - Used to hold plastic to metal |
|
Screw - Wafer head machine screw - M3, 6mm long, No. 2 Phillips recess - Secures metal to sheet metal |
|
Screw - Machine screw with captured washer - M3 X 29.5mm long |
|
Screw - M4 X 12mm Indented pan head screw |
|
Fuse - Low voltage power supply fuse - 110V |
|
Spring - Shutter arm spring - Provides tension for shutter arm |
|
Flag - Sensor flag - Short rod with two flat flags and a curved end flag |
|
Latch - Left side alignment latch for front door |
|
Screw - Machine screw - M3, 30mm long with self-tapping threads - Typically used to hold metal to plastic |
|
Clip - Retaining clip |
|
Screw - M3 pan-head Phillips screw with flat washer - 8mm long |
|
Screw - Screw - M3 X 6mm long |
|
Cable - Jetlink connector grounding cable |
|
Screw - M3 pan head phillips screw with captive flat and split-lock washers - 8mm long |
|
Gear - 21 tooth gear for HP LaserJet M9040 MFP |
|
Flag - Sensor flag - Short rod with two flags on it |
|
Guide - Paper guide for HP LaserJet 9040 9050 Series |
|
Mount - Rear Fuser Assembly mount |
|
Screw - Machine screw with captured washer - M5 X 12 - Typically used to secure plastic parts to metal |
|
Screw - Machine screw with captured washer - M3 X 29.5mm long |
|
Arm - Shutter arm for HP LaserJet M9040 MFP |
|
Spring - Torsion spring - Provides tension for paper selector switch |
|
Flag - Sensor flag - Long rod with forked flag toward one end and curved flag at the other |
|
Lever - Microswitch lever - Activates interlock switches from both the front and left doors |
|
Screw - Screw - M4 X 8mm long |
|
Cover - Blanking cover - Located behind the cartridge release lever |
|
Spring - Torsion spring - Provides tension for bin full flag |
|
Cable - High voltage power supply ribbon cable |
|
Screw - Stepped screw - Larger shoulder screw used to fasten the left side cover to the frame of the 2,000-sheet paper feeder assembly (two used) |
|
Screw - Wafer head machine screw, clear zinc, 3M X 8mm - Secures plastic to metal |
|
Clip - E-ring retainer clip |
|
Cable - Cable assembly - Grounding cable for tray 1 |
|
Spring - Laser shutter spring - Provides tension for laser shutter |
|
Spring - Compression spring - Provides tension for ON/OFF switch |
|
Spring - Compression spring - provides tension for right cover latch |
|
Cap - Right cover cap |
|
Screw - Machine screw with attached washer - M3, 10mm - Used to hold plastic to metal |
|
Screw - Wafer head machine screw - M3, 6mm long, No. 2 Phillips recess - Secures metal to sheet metal |
|
Manual - Send RFQ below for updated Price and Description |
|
Screw - M3 X 6 screw for HP LaserJet 9040 9050 Series |
|
Screw - M3 X 8 Screw for HP LaserJet 9040 9050 Series |
|
Cable - Upper cable guide assembly |
|
Service_Guide_PH - HP LaserJet 9000DN Printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams. |
|
Accumulator - Accumulator assembly - Holds paper until print job finish then moves to stapler or correct output bin |
|
Screw - Stabilizing screw for the 2,000-sheet feeder - Mounts on right side of the 2,000-sheet paper feeder assembly (two used) |
