Part |
Description |
|
PC_Board - Formatter (Main Logic) board |
|
PC_Board - Formatter (Main Logic) board |
|
Scanner - Contact image sensor assembly - Scanner LED |
|
PC_Board - ECU board - Engine controller unit/power system controller board - Logic and power supply combined PCA - 110V |
|
PC_Board - ECU board - Engine controller unit/power system controller board - Logic and power supply combined PCA - 220V |
|
Maintenance_Kit - Maintenance Kit (220V) - Includes fuser, separation pad kit, transfer roller, pressure roller, pickup roller, exit roller assembly and idler roller - Procedure requires service manual |
|
Maintenance_Kit - Maintenance Kit (120V) - Includes fuser, separation pad kit, transfer roller, pickup roller, exit roller assembly, and idler roller - Procedure may require service manual (sold separately). |
|
Laser_Scanner - Laser/scanner assembly |
|
Fuser_Assembly - Heating element assembly (For 100V to 120V operation) - Bonds the toner to the paper with heat |
|
Control_Panel - Control panel assembly |
|
Cartridge - Black (Micro-Fine) toner (EP) cartridge - Will print approximately 2,500 pages based on a 5 percent print density |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin high density IEEE 1284C (M) connector (type C) - 10m (33ft) long |
|
Door - Printer door assembly |
|
Fuser_Assembly - Heating element assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat |
|
Scanner - Document scanner assembly - Includes motor, rollers and guides - Does NOT include image sensor assembly |
|
PC_Board - LIU - Phone line input unit - US only |
|
Pickup_Assembly - Paper pickup assembly |
|
PC_Board - LIU - Phone line input unit - World wide unit |
|
Cartridge - Black (Micro-Fine) toner (EP) cartridge - Will print approximately 2,500 pages based on a 5 percent print density |
|
Roller - Pickup roller assembly - Shaft/roller assembly that feeds paper from paper input assemblies - Also order separation pad kit |
|
Cable - IEEE 1284 Bi-Tronics parallel interface cable - DB-25 (M) connector (type A) to IEEE 1284C 36-pin (M) connector (type C) - 2.0m (6.6ft) long |
|
Cable - IEEE 1284 Bi-Tronics parallel interface cable - DB-25 (M) connector (type A) to IEEE 1284C 36-pin (M) connector (type C) - 2.0m (6.6ft) long Miniconnector |
|
Cartridge - Epa yield black toner |
|
Cartridge - 06a yield black toner |
|
Guide - Upper paper guide - Guides paper through scanner path |
|
Cable - 8120-8724 IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin high density IEEE-1284C (M) connector (type C) - 3.0m (9.8ft) long mini connector. |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin high density IEEE 1284C (M) connector (type C) - 10m (33ft) long mini-connector. |
|
Torque_Limiter - Torque limiter - Limits rotation of feed rollers |
|
Frame - Paper feed frame - Main frame that parts such as pickup roller assembly and separation pad are installed on |
|
Pad - Printer separation pad kit - Includes main pad, spring, and two smaller subpads - Also order pickup roller assembly (RY7-5008-000CN) |
|
Roller - Pressure roller - Shaft/roller with gear on left side of roller located underneath the heating element |
|
Manual - LaserJet quick reference service guide (monochrome) - Volume IV |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin high density IEEE 1284C (M) connector (type C) - 3.0m (9.8ft) long -- Mini Connector |
|
Roller - Pressure roller - Shaft/roller with gear on left side of roller located underneath the heating element |
|
Solenoid - Paper pickup solenoid |
|
Roller - Paper pickup roller for unit. This is the roller that goes on the paper pick up roller shaft - shaft roller assembly that feeds paper from paper input assembly. Roller only. (shaft and roller see part number RG5-3486-040CN) |
|
Tray - Printer paper input tray - Rear paper input support |
|
Delivery - Delivery assembly - Attaches to the lower center area of the internal chassis - Includes four White 'multi-ridged' and two other delivery rollers and their associated springs |
|
Motor - Scanner motor for HP LaserJet 3150 Series |
|
Motor - HP Motor for LaserJets |
|
Cable - Telephone cable with ferrite - The wall socket end has both a 4-pin (M) connector and a 4-pin (F) tap - The other end has an RJ-ll (M) connector - 2.9m (9.7ft) long (United Kingdom) |
|
Power_Cord - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 220V in Denmark) |
|
Cable - Telephone cable (France) |
|
Roller - Paper pickup roller assembly for document scanner |
|
Plate - Chassis bottom plate |
|
Guide - Duct 1 - For Paper output and aids in cooling |
|
Guide - Duct 1 - For Paper output and aids in cooling |
|
Guide - Separation guide assembly - Includes the face-up/face-down paper selection lever/deflector and Fuser Assembly exit roller assembly |
|
Cover - Right side chassis cover |
|
Guide - Transfer guide assembly (Ribbed plastic piece) - Mounting support for the transfer roller |
|
Cover - Back side chassis cover |
|
Cover - Top front chassis cover |
|
Tray - Single sheet input slot - Manual feed tray |
|
Separator - HEWLETT PACKARD Laserjet sub pad assembly right and left pads. |
|
Cover - Left back side chassis cover |
|
Roller - Transfer roller - Located underneath toner (EP) cartridge |
|
Cable - Cable assembly for HP LaserJet 3150 Series |
|
Tray - Input bin assembly - Paper input supply bin |
|
Sensor - Paper sensor flag/arm - Detects leading and trailing edges of paper |
|
Speaker - Speaker for HP LaserJet 3100 Series |
|
Gear - Fuser release assembly - Gear/tab assembly on left side of internal main chassis - Includes housing, two gears, and fuser release tab |
|
Gear - Gear kit '#3' - Includes first four gears driven by main motor |
|
Guide - Duct 2 - Helps provide heat dissipation |
|
Cable - Telephone cable (Netherlands) |
|
Interlock - Interlock assembly - Detects if EP (Toner) door is open |
|
Cable - Grounding cable - Document scanner grounding cable |
|
Shield - RFI shield for HP LaserJet 3100 Series |
|
Cable - Telephone cable (Germany) |
|
Guide - Fuser cable guide |
|
Cover - Cap - Covers hole in chassis - Located on the front left side |
|
Guide - Fuser Assembly paper guide |
|
Protector - Jam prevention protector - Installs in the delivery assembly - Allows paper jams to be cleared without damaging the printer |
|
Cover - Engine self test switch cover |
|
Mount - Speaker mount/cover |
|
Connector - Fuser electrical connector |
|
Shaft - Idler roller shaft assembly |
|
Holder - Right side hinge holder |
|
Plate - Grounding plate - Chassis ground for back plate |
|
Plate - Gear support plate - For gear kit #2 |
|
Guide - Sheet arching guide - 2 used - Mylar strips that direct paper to output bin |
|
Foot - Rubber foot - Replacement rubber foot for the bottom support (four used) |
|
Guide - Paper guide - Inside spur assembly |
|
Holder - Gear holder - For gear kit #1 |
|
Guide - Sheet guide - Mylar strip paper guide |
|
Spring - Spring - Used with the #1 delivery rollers |
|
Arm - Paper exit sensor arm |
|
Bushing - Fuser exit roller bushing |
|
Strap - Door strap - ADF door support |
|
Spring - Spring - Located underneath paper kick plate |
|
Guide - Cable guide for HP LaserJet 3100 Series |
|
Lever - Paper path lever - Selects 'In Order' or 'Straight Thru' |
|
Cover - Right side printer door hinge cover |
|
Roller - Fuser exit roller assembly - Shaft and rollers - Attaches to separation guide assembly |
|
Holder - Left side hinge holder |
|
Plate - Fuser pressure plate - Guides paper over fuser roller |
|
Cable - Cable assembly for HP LaserJet 5L Series |
|
Ground - Case grounding strap (metal) |
|
Spring - Grounding spring - Grounds kick plate |
|
Plate - Grounding plate - Chassis ground clips |
|
Cable - Cable assembly for HP LaserJet 5L Series |
|
Gear - Pressure roller shaft gear |
|
Spring - Compression spring - Provides tension for pressure plate |
|
Spring - Spring - For paper exit sensor arm |
|
Overlay - Keypad overlay - Allows customer to notate specific fax numbers to the one touch keypad |
|
Clamp - Cable clamp - Holds cable in place |
|
Bezel - I/O bezel - I/O connector bezel |
|
Leg - Left leg - Small leg on left side of paper kick plate |
|
Spring - Spring - Used with the #2 delivery rollers (two used) |
|
Guide - Right side toner cartridge guide |
|
Holder - Formatter cable guide holder |
|
Cover - Pressure release lever cover - Paper jam release lever |
|
Guide - Left side toner cartridge guide - Back half of guide |
|
Lever - Face-up/face-down shaft and media deflector |
|
Cable - Ribbon cable - Has 30-pin (M) connectors - 9.1cm (3.6in) long |
|
Spring - Grounding spring - Grounds transfer guide |
|
Plate - Formatter board mounting plate |
|
Tray - Printer paper output tray - Behind scanner input support |
|
Cable - Cable assembly for HP LaserJet 5L Series |
|
Spacer - ECU PC board spacer between PC board and bottom plate |
|
Guide - Frame cable guide |
|
Bushing - Pickup roller bushing |
|
Roller - Delivery roller #1 - White 'Multi-ridged' roller - Four are used in delivery assembly |
|
Spacer - Spacer - Between cable guide and printer door on left side |
|
Roller - Exit roller assembly - Shaft with four black rollers - Rollers are aligned with and work in conjunction with the white 'Multi-ridged' rollers of the delivery assembly |
|
Guide - Paper guide - Outside spur assembly |
|
Cable - Cable assembly for HP LaserJet 6L Series |
|
Cable - CIS grounding cable - Scanner grounding cable |
|
Cable - Telephone cable (Australia, New Zealand) |
|
Lever - Fuser release lever - Part of fuser release assembly |
|
Support - Left side pressure roller support |
|
Support - Right side pressure roller support |
|
Sleeve - Cable sleeve - Protective tube for control panel cable |
|
Cable - Telephone cable (Australia/Ireland) |
|
Leg - Right leg - Small leg on right side of paper kick plate |
|
Bushing - Pressure roller bushing |
|
Guide - Transfer roller guide |
|
Cover - Left side printer door hinge cover |
|
Cable - Cable assembly for HP LaserJet 5L Series |
|
Bushing - Exit roller bushing |
|
Roller - Delivery roller #2 |
|
Cable - Cable assembly for HP LaserJet 6L Series |
|
Gear - Gear kit - Includes first five gears on front left side area of the internal chassis - Gear kit #1 |
|
Guide - Pressure roller ground guide - Protects pressure roller ground cable |
|
Guide - Cable guide - For the control panel cable |
|
Cover - Bottom front cover |
|
Guide - Document scanner guide |
|
Guide - Right side toner cartridge guide - Back half of guide |
|
Plate - Paper kick plate (middle) |
|
Shield - Back shield - Reinforcement plate |
|
Clip - Pickup roller shaft grounding clip |
|
Roller - Idler roller for feed assembly |
|
Guide - Formatter cable guide |
|
Cable - Ribbon cable - Has two 26-pin (M) edge connectors - 15.1cm (6.0in) long |
|
Clamp - Wire clamp - Holds wire/cable in place |
|
Cover - Front left side chassis cover |
|
Power_Cord - Power cord (Dove Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in the U.K., Hong Kong, Singapore, Malaysia) |
|
Power_Cord - Power cord (dove gray) - 2.3M (7.5ft) long - Has straight (F) receptacle (For 240VAC in the United Kingdom, Hong Kong, Singapore, Malaysia) |
|
Sleeve - Document carrier sleeve - 2 full size and 2 half size sleeves - Sleeve sealed on three sides |
|
Pad - Scanner separation pad kit - Kit includes separation pad, separation backing pad and separation pad holder |
|
Power_Cord - Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 120V in the USA, Canada, Mexico, Philippines, and Taiwan) |
|
Clutch - Clutch - On left side of pickup roller assembly shaft |
|
Clutch - Clutch - On left side of pickup roller assembly shaft |
|
Cable - Telephone cable (2-wire) - RJ11 (M) connectors - 3m (10ft) long (USA, Canada, Mexico, Latin America, Greece, Poland, Saudi Arabia, Portugal, and Spain) |
|
Power_Cord - Power cord (Flint Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in Australia, New Zealand) |
|
Pad - Backing pad - Plastic backing support for separation pad |
|
Power_Cord - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 220V in Europe, Saudi Arabia, South Africa, India, and Korea) |
|
Pad - Separation pad - Document scanner separation pad |
|
Connector - Fuser electrical connector |
|
Pad - Document scanner separation pad holder |
|
Feeder - Feed assembly - Has idler roller, sensor flag and paper input sensor |
|
Arm - Paper exit sensor arm |
|
LaserJet - HP LaserJet 3150 Printer |
|
Lubricant - Grease for HP LaserJet 5L Series |
|
Tray - ADF input tray - Automatic document feeder input support |
|
Service_Guide_PH - HP LaserJet 3150 Printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams. |
|
Tray - ADF output paper tray - Automatic document output support |
