Part |
Description |
|
Print_Server - External JetDirect 300X LAN interface module - Interfaces a parallel printer to an ethernet 10Base-T (RJ-45) or 100Base-TX (RJ-45) LAN |
|
Print_Server - External JetDirect 170X LAN interface module - Interfaces a parallel printer to an ethernet 10Base-T (RJ-45) LAN |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 3.0m (10ft) long |
|
Print_Server - External JetDirect 70X home print server - Uses telephone wiring to establish a local area network for remote printer operation - For Microsoft Windows 95/98/NT 4.0 - Uses 1Mbps HomePNA version 1.0 signals |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 1.8m (6ft) long |
|
Roller - Pivot feed roller - Shaft with 4 hard rollers - Does not include other items such as gear or encoder |
|
Duplexer - Replacement duplexer module assembly - installs in rear of printer (in place of the rear clean out door assembly) - for performing two-sided printing. |
|
Duplexer - Duplexer Module - REPLACEMENT DUPLEXER MODULE ASSEMBLY - INSTALLS IN REAR OF PRINTER (IN PLACE OF THE REAR CLEAN OUT DOOR ASSEMBLY) |
|
Duplexer - Replacement duplexer module assembly - installs in rear of printer (in place of the rear clean out door assembly) - for performing two-sided printing (c6463a) |
|
Cartridge - HP 78XL Tri-color InkJet Print Cartridge - Prints approximately 1200 color graphic pages (North America) |
|
Power_Supply - HP Ac Adapter (31V/ 2.42A) Power Supply unit for HP Business InkJet Printers. |
|
Strip - Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position |
|
Guide - Lower paper guide housing (Does NOT include any attaching parts) |
|
Carriage - Carriage assembly - Includes carriage, felt, felt retainers, ink cartridge latches - Does not include trailing cable, PC board, belt attachment hardware, or slider |
|
Cartridge - Tri-color ink economy print cartridge - Prints approximately 450 pages based on 13.5% total density (4.5% for each color) on a 8-inch by 10-inch print area (Europe) |
|
Roller - Pivot and feed roller assembly - Includes pivot and shaft with 4 rollers, gears, encoder disk, bearings - Feeds the media under the carriage assembly and print cartridges |
|
PC_Board - Carriage PC board - Contains the print cartridge control circuitry - For Japan only |
|
Power_Supply - Power Supply PC Board |
|
Pivot - Pivot - Large plastic item installed over the Feed Roller Assembly |
|
PC_Board - Interconnect PC board - Small square PC board with 4 contact pads for the duplexer module |
|
Guide - Upper paper guide (Does NOT include any attaching parts) - Spring loaded flat plate that presses the media against the top of the feed roller assembly - Caution: this part can easily be broken |
|
Cartridge - HP 78 Tri-color InkJet Print Cartridge - 19ml - Prints approximately 450 color graphic pages (North America) |
|
PC_Board - Power supply PC board |
|
Cartridge - HP InkJet Crtg 45A Black Large NAM |
|
Disk - Paper motor encoder disk |
|
Belt - Carriage belt - Moves the carriage assembly across the carriage rod |
|
Roller - Pickup roller - Shaft with large rollers - Does not include other items such as gear or bearings |
|
Sensor - Spot sensor assembly |
|
Motor - Service station motor assembly - Includes PC board and gear |
|
Absorber - Sponge - Absorbs excess ink and debris from cleaning print cartridges |
|
Peg - Separator Peg - Pushes up the separator pad during the paper pick operation |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
|
Cable - Universal serial bus (USB) interface cable - Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long |
|
Door - Rear cleanout door assembly - Paper jam cleanout door |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
|
PC_Board - Paper drive assembly encoder PC board |
|
Tray - Input paper tray - Holds up to 100 sheets of cut sheet paper |
|
Sled - Long roller sled - Installed over rear roller |
|
Sled - Short roller sled - Installed over rear roller |
|
Roller - Pickup roller assembly - Shaft with large rollers, gear, and 2 bearings - Feeds paper from the paper input tray into the print mechanism |
|
Motor - Carriage motor assembly (Includes pulley) |
|
Power_Cord - Power cord (Flint Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 120V in the United States, Canada, Brazil, Latin America, and Saudi Arabia) |
|
PC_Board - Interconnect PC board - Small square PC board with four contact pads for the duplexer module |
|
Bar - Paper pusher bar (Bar with three levers) - Pushes the printed paper from the pivot and feed roller assembly on to the output paper tray |
|
Kicker - Kicker bar - Restacks paper in paper input tray stack after the top sheet is picked |
|
Stickers - Square re-stickable InkJet stickers - HP bright white 6.35cm (2.5in) square stickers with 3M 'Post-it' adhesive - A size (8.5 x 11-inches) - 10 sheets per package with nine stickers per sheet |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
|
Cover - Top cover for HP DeskJet 952C |
|
Cable - Cable assembly - Has many connectors: a 30-pin (F), a 2-pin (F), two 3-pin (F), a 4-pin (F), two 5-pin (F), and an 8-pin (F) - Overall length is 67.3cm (26.5in) |
|
Backbone - Backbone - Large metal item attached to the front of the printer base |
|
Slider - Slider for carriage assembly - Rides along the upper guide rail on the print mechanism chassis |
|
Rail - Paper pusher rail |
|
Retainer - Felt retainer - Holds the carriage lubrication felt on both sides of the pen carriage assembly |
|
Cover - Rear connector cover |
|
Support - Side latch spring support |
|
Cover - Left side cover |
|
Spring - Shifter spring - Provides tension on the pivot |
|
Gear - Cluster gear (large gear) |
|
Bearing - Roller bearing for HP DeskJet 6940 Series |
|
Lever - Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker |
|
Housing - Housing for power supply PC board |
|
Cover - Right side cover |
|
Flag - DOOPS flag - Lifts the out of paper sensor (OOPS) flag out of the way when media is moving back towards the duplexer module - Mounts on the upper paper guide behind OOPS flag |
|
Cam - Drawer cam - Short, spring loaded lever attached to the paper tray frame - Used to draw input tray into position |
|
Link - Kicker bar cam link (spring loaded) |
|
Blade - ESD blade for HP DeskJet 870C Series |
|
Gear - Transfer gear (double gear) |
|
Clip - Service station ESD grounding clip |
|
Gear - Gear - 48 tooth |
|
Handle - Paper input tray right handle |
|
Spring - Pinch spring - Provides tension on upper paper guide |
|
Gear - Encoder gear for HP Color Copier 260 |
|
Clip - Rod mounting clip |
|
Spring - Rod spring - Installed on right side of backbone |
|
Spring - Tray spring - Installed near front of paper tray frame - Used in conjunction with the drawer cam to hold the paper input tray assembly in position |
|
Beam - Belt attachment beam (I-shaped) - Used to secure the belt attachment tower to the carriage assembly |
|
Guide - Flip guide (Curved plastic piece with large fins) |
|
Handle - Paper input tray left handle |
|
Lifter - Separator peg lifter - Used to lift and retain the separator peg under spring tension - Caution: if this part is installed incorrectly, printer will NOT function |
|
Wingframe - Right wingframe assembly - Supports paper from the print mechanism prior to exiting to the paper tray frame assembly |
|
Keypad - Keypad and cover assembly |
|
Roller - Rear roller (Black) - Between paper and rear paper guide |
|
Shaft - Drive shaft with molded gears on each end |
|
Button - Top cover latch button |
|
Cable - Cable assembly - Has 4-pin (F) connectors - 4.9cm (1.9in) long |
|
Adjuster - Paper tray width/length adjuster - Holds media against right wall of input tray or against the rollers |
|
Tray - Paper output tray assembly (floor, photo) - Includes trays, springs, sensors |
|
Pallet - Pallet/link assembly - Installed between spittoon and sled cap assembly - Mounting platform for the wiper and capping systems parts |
|
Knob - Latch knob - Mounts on the rear paper cleanout door assembly |
|
Frame - Paper tray frame assembly - Includes paper tray frame, paper tray cover, paper tray side covers, springs, and cam |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 240V in the United Kingdom) |
|
Spring - Cap spring - Provides upward pressure on the sled cap assembly to seal the parked print cartridges |
|
Spring - Spring for rear rollers |
|
Guide - Slot cover flap (Curved plastic piece with small fins) |
|
Gear - Gear - 72 tooth - For roller shaft |
|
Flag - OOPS flag - (out of paper) media sensor lever flag - Mounts on the top right edge of the upper paper guide |
|
Tray - Paper output photo tray cover |
|
Spitton - Spittoon base - The bottom and main housing of the service station assembly - Holds any residual ink from the print cartridge cleaning process |
|
Base - Belt attachment base - Mounts on rear of carriage assembly - Covers carriage PC board and holds belt attachment tower |
|
Bracket - Paper drive assembly bracket - Paper drive motor, cluster gear and the encoder PC board all mount to this item |
|
Guide - Inner paper guide (Includes antistatic brush) - Guides the paper through the print mech and over the upper paper guide |
|
Spring - Belt tension spring - Provides tension for carriage belt |
|
Sled - Sled cap assembly - Top cover of the service station assembly - Includes print cartridge caps (gaskets which keep the cartridges from drying out when not printing) |
|
Rod - Carriage rod - Slider/guide rod for the pen carriage assembly |
|
Spring - Lifter spring - Provides upper tension on the kicker bar (cam follower) lift plate |
|
Clip - Capture clip for HP DeskJet 952C |
|
Guide - Rear guide - Large plastic piece in the duplexer in which the rollers and springs mount on |
|
Gear - Dual gear - 20 tooth/60 tooth |
|
Cover - Paper tray right side cover |
|
Backbone - Backbone - Large metal item attached to the front of the printer base |
|
Ferrite_Assembly - Trailing cable ferrite |
|
Cover - Paper tray left side cover |
|
Gear - Pickup roller gear assembly |
|
Vent - Cap vent - For equalizing the print cartridge capping pressure |
|
Spring - Separator spring - Provides pressure between separator assembly and the center drive roller |
|
Foot - Rubber foot - Replacement rubber foot for the bottom of the printer (four used) |
|
Guide - Encoder disk guide |
|
Wiper - Wiper assembly - Metal base with plastic wipers |
|
Bracket - IEC connector bracket - Holds the power cord socket |
|
Support - Upper paper guide support - Support bracket which attaches to the print mech frame for mounting the upper paper guide |
|
Clip - Ferrite clip - Used to hold trailing cable ferrite in place |
|
Spring - Envelope spring assembly - Aligns envelopes when inserted into the envelope feed slot |
|
Tower - Belt attachment tower - Used to attach the carriage belt to the carriage assembly |
|
Guide - Inner guide - The large, curved plastic guide installed in the rear of the duplexer surrounding the roller shafts |
|
Door - Print cartridge access door assembly - Includes door and window |
|
Guide - Lower paper guide (Curved plastic paper guide) - The six guide rollers mount on this piece |
|
Wingframe - Left wingframe assembly - Supports paper from the print mechanism prior to exiting to the paper tray frame assembly |
|
Rail - Upper rail for HP DeskJet 952C |
|
Guide - Media input length adjuster assembly - Includes both coarse and fine length adjusters |
|
Guide - Fine length adjuster (Only) |
|
Roller - Roller shaft assembly - Shaft with three large rollers, two bearings, and one gear |
|
Motor - Paper drive motor assembly - Includes pulley |
|
Plate - Pressure plate - Mounts in the rear of the paper input tray - Used to push the paper stack into the feed roller |
|
Belt - Paper drive belt |
|
Button - Side latch button |
|
Spring - Rear roller spring - Flexible axle for rear roller |
|
Gear - Cluster gear for HP OfficeJet K60 |
|
Latch - Wedge latch for HP DeskJet 950C Series |
|
Cover - Cover plate for HP DeskJet 970C Series |
|
Gear - Feed roller idler gear |
|
Spring - ESD spring - Installed between ESD blade and carriage PC board |
|
Spring - Latch spring - Provides friction for the knob on the rear cleanout door assembly |
|
Snap - Cap snap - Installed between pallet/link assembly and sled cap assembly - Used to hold the cap spring |
|
Separator - Separator pad for HP DeskJet 700 Series |
|
Plate - Shift plate assembly - Five plastic gears held in a two piece plastic frame - Attaches to feedroller assembly |
|
Gear - Pivot plate assembly - Three small gears, a washer, and a spring mounted on a plastic carrier |
|
Roller - Pinch roller - Provides downward pressure on media as it passes by upper paper guide |
|
Latch - Plastic latch (Y-shaped) |
|
Spring - Encoder spring - Provides tension for encoder strip |
|
Guide - Spring guide for HP DeskJet 880C Series |
|
Cover - Cover - For rear paper cleanout door assembly |
|
Gear - Kicker bar cam gear - Gear with cam lobe and offset pin |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 240V in South Africa and India) |
|
Pad - Lubricating felt pad (C-shaped) - Lubricates the carriage assembly as it moves across the carriage rod |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 220V in China) |
|
Slider - Slider for carriage assembly - Rides along the upper guide rail on the print mechanism chassis |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 240V in Australia and New Zealand) |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 100V in Japan) |
|
Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
|
Cover - Top cover (Bonnet) |
|
Tray - Photo Paper Input Drawer |
|
Stickers - Round re-stickable InkJet stickers - HP bright white 6.35cm (2.5in) round stickers with 3M 'Post-it' adhesive - A size (8.5 x 11-inches) - 10 sheets per package with nine stickers per sheet |
|
Cable - Carriage assembly flex cable - Has 24-pin (M) edge connectors - 38.6cm (15.2in) long |
|
Turnaround_Assembly - Turnaround assembly - Provides carriage belt tension - Does not include spring |
|
Power_Cord - Power cord (Black) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 220V in South Africa, India, and Saudi Arabia) |
|
Paper - Media for HP C8244A |
|
Paper - Media for HP C6465A |
|
Paper - Deluxe glossy photo paper - A size (8.5 x 11-inches) - 20 sheets per pack |
|
Film - Premium InkJet transparency film - A4 size (21.0cm x 29.7cm) - 20 sheets per package |
|
DeskJet - DeskJet 952C Printer |
|
Paper - Media for HP C6428A |
|
Paper - Media for HP C8136A |
|
Paper - Printable Expressions all occasions card kit - Includes 20 greeting cards and envelopes, and a CD-ROM with 24 original pieces of art |
|
Paper - Brochure and flyer paper - Glossy on both sides - A size (8.5 x 11-inches), 98 brightness - 50 sheets |
|
Paper - Premium Plus glossy InkJet photographic paper - 10.0cm (3.9in) x 15.0cm (5.9in) - 20 sheets per package |
|
Power_Cord - Power cord (Flint Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 220V in Europe, Asia Pacific, Germany, Spain, France, Netherlands, Switzerland, Italy, and Portugal) |
|
Paper - Media for HP C5894A |
|
Paper - Media for HP C5894A |
|
Paper - Media for HP C8136A |
|
Spring - Send RFQ below for updated Price and Description |
|
Cartridge - InkJet Cartridge 78 Large Color EUR |
|
Cartridge - InkJet Crtg 45A Black Large Can |
|
Cartridge - Black print cartridge (economy) - Prints approximately 415 pages based on 5% density on a 8 inch by 10 inch print area (USA) |
|
Cartridge - HP 45 Economy Black InkJet Print Cartridge - Prints approximately 415 pages based on 5% density on a 8-inch by 10-inch print area (Asia Pacific) |
|
Cartridge - HP 45 Economy Black InkJet Print Cartridge - Prints approximately 415 pages based on 5% density on a 8-inch by 10-inch print area (Latin America) |
|
Cartridge - InkJet Cartridge 78 Color Can |
|
Paper - Photo Greeting Cards (White, Matte) - A size (8.5 x 11-inches), half fold, pre-scored - Includes 20 cards and 20 envelopes |
|
Printhead - Black print cartridge (high capacity) - Prints approximately 840 pages based on 5% density on a 8-inch by 10-inch print area (Europe) |
|
Paper - Photo quality InkJet paper - With two sided semi-gloss finish - A size (8.5 x 11-inches) - 25 sheets per package |
|
Paper - Media for HP C6429C |
|
Cartridge - InkJet Cartridge 78 Large Color AP |
|
Paper - Photo Quality InkJet Paper (Matte) - With two sided matte finish - A size (8.5 x 11-inches) - 100 sheets |
|
Paper - Media for HP Q5761A |
|
Paper - Media for HP C6429C |
|
NamePlate - Nameplate - C6428B DeskJet 952C printer logo |
|
Cartridge - InkJet Cartridge 78 Large Color LAR |
|
Cartridge - InkJet Cartridge 78 Color AP |
|
Cartridge - Black print cartridge (economy) - Prints approximately 415 pages based on 5% density on a 8-inch by 10-inch print area (Canada) |
|
Paper - Greeting card paper pack (White) - A size (8.5 x 11-inches) - Includes 20 sheets and 20 envelopes |
|
Paper - Media for HP C8127A |
|
Service_Guide_PH - HP DeskJet 952C Printer Reference Guide - Contains information such as product information, operation overview, paper behavior, mainenance, ink safety, and removal / replacement of parts |
|
Cartridge - InkJet Cartridge 78 Large Color Can |
|
Paper - InkJet non-glossy LX paper - A4 size (21.0cm x 29.7cm) - 200 sheets per package |
|
Cartridge - InkJet Crtg 45A Black Large AP |
|
Cartridge - Black print cartridge (high capacity) - Prints approximately 840 pages based on 5% density on a 8-inch by 10-inch print area (Latin America) |
|
Cartridge - InkJet Cartridge 78 Color LAR |
|
Paper - HP Premium Plus Glossy Photo Paper - A size (8.5 x 11-inches) - 20 sheets |
|
Paper - Media for HP C6749A |
|
Bearing - Bearing for roller shaft |
|
Paper - Premium Photo Paper (Glossy) - A size (8.5 x 11-inches) - 50 sheets |
|
Paper - Premium Photo Paper (Glossy) - A size (8.5 x 11-inches) - 15 sheets |
|
Paper - Media for HP C8952A |
|
PC_Board - Carriage PC board - Contains the print cartridge control circuitry - For Japan only |
|
Cartridge - Black print cartridges (high capacity) - (two-pack of 51645A) each prints approximately 840 pages based on 5% density on a 8-inch (20.3cm) by 10-inch (25.4cm) print area (USA) |
|
Paper - HP Textured Half-fold Greeting Cards (White) - A size (8.5 x 11-inches) |
|
Print_Server - JetDirect 300X external print server module (10Base-T and 100Base-TX) - Connects between printer parallel port and LAN network |
