Part |
Description |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 3.0m (10ft) long |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) (type A) to 36-pin (M) Centronics (type B) - 1.8m (6ft) long |
|
Print_Server - External JetDirect LAN interface module with EtherTwist (10Base-T and ThinLAN) (10Base-2) input connectors and three parallel (DB-25) output connectors |
|
Belt - Carriage drive belt - Moves printhead side to side |
|
Module - External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors |
|
Roller - Pivot feed roller - Shaft with 4 hard rollers - Does not include other items such as gear or encoder |
|
Carriage - Ink cartridge carriage assembly - This item should be replaced only by trained, experienced service personnel |
|
Spitton - Spittoon base - The bottom of the service station assembly |
|
Strip - Encoder strip - Clear strip with position marks - Used by the sensor in the carriage assembly to determine position |
|
Module - External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors |
|
Power_Supply - Power module (wall mount, MEI-AH ED12007) - Input voltage 230VAC, 47/53Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Europe and Israel) |
|
Roller - Pivot assembly - Large plastic Item below the feed roller assembly - Picks and feeds media through print mechanism - Should be replaced only by experienced service personnel |
|
Power_Module - Pwer supply, 13v/300ma jpn |
|
Power_Module - Power supply module - 100V/240V, 50/60Hz - Requires separate AC power cord - For worldwide use |
|
Roller - Pivot feed roller assembly - Shaft with small rollers and paper encoder - This item should be replaced only by trained, experienced service personnel |
|
Strip - Wear strip - Long, spring loaded strip mounted in top of backbone - Used to ensure smooth ink cartridge carriage motion |
|
Guide - Upper paper guide - Guides media through paper path |
|
Cartridge - No. 17 Tri-color ink print cartridge (USA) |
|
Cartridge - No. 15 Black ink print cartridge - 25 ml ink (USA) |
|
Roller - Pickup roller - Shaft with large rollers - Does not include other items such as gear or bearings |
|
Disk - Paper motor encoder disk |
|
Motor - Service station motor assembly - Includes PC board and gear |
|
Door - Top/front access door assembly - Print cartridge access door with tangerine colored window - Includes installation instructions |
|
Door - Top/front access door assembly - Print cartridge access door with strawberry colored window - Includes installation instructions |
|
Door - Top/front access door assembly - Print cartridge access door with grape colored window - Includes installation instructions |
|
Door - Top/front access door assembly - Print cartridge access door with lime window - With installation instructions |
|
Absorber - Spittoon sponge - Absorbs excess ink from cartridges |
|
Power_Module - Wall mount power supply module (MEI-AH ED12010) - 220-250VAC input, 47-53Hz - 13VDC output, 800mA, 10.4 watts (South Africa) |
|
Cable - Universal serial bus (USB) interface cable - Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long |
|
Power_Supply - Power module (wall mount)- Input voltage 220-250VAC, 47/53Hz - Output voltage 13VDC, 800mA, 10.4W (Worldwide) |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
|
Roller - Pickup roller assembly - Shaft with large rollers, gear, and 2 bearings - Picks paper from paper input tray - Available for trade sales in Europe and Asia/Pacific - Available for authorized service centers only in USA |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
|
Power_Module - Power module (wall mount) - Input voltage 100VAC, 47/63Hz - Output voltage 13VDC, 800mA, 10.4 watts (for use in Japan) |
|
Door - Top/front access door assembly - Print cartridge access door with Strawberry colored window - Replaces the existing door |
|
Door - Top/front access door assembly - Print cartridge access door with Lime colored window - Replaces the existing door |
|
Door - Top/front access door assembly - Print cartridge access door with Grape colored window - Replaces the existing door |
|
Door - Top/front access door assembly - Print cartridge access door with Blueberry colored window - Replaces the existing door |
|
Door - Top/front access door assembly - Print cartridge access door with Tangerine colored window - Replaces the existing door |
|
Door - Rear cleanout door assembly - Paper jam cleanout door |
|
Door - Top/front access door assembly - Print cartridge access door with blueberry colored window - Does not include installation instructions |
|
Motor - Carriage motor assembly (Includes pulley) |
|
Door - Top/front access door assembly - Print cartridge access door with lime colored window - Does not include installation instructions |
|
Door - Top/front access door assembly - Print cartridge access door with strawberry colored window - Does not include installation instructions |
|
Door - Top/front access door assembly - Print cartridge access door with tangerine window - Without installation instructions |
|
Door - Top/front access door assembly - Print cartridge access door with grape colored window - Does not include installation instructions |
|
Power_Module - Universal AC power adapter - wide-range, 40c - Requires separate country-specific power cord |
|
Power_Cord - Power cord (Flint Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 120V in the United States, Canada, Brazil, Latin America, and Saudi Arabia) |
|
Door - Top/Front access door assembly - Print cartridge access door with emerald color window |
|
Stickers - Square re-stickable InkJet stickers - HP bright white 6.35cm (2.5in) square stickers with 3M 'Post-it' adhesive - A size (8.5 x 11-inches) - 10 sheets per package with nine stickers per sheet |
|
Cable - IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin Centronics (M) connector (type B) - 2.0m (6.6ft) long |
|
Power_Module - Wall mount power supply module (MEI-AH ED12010) - 100VAC input, 47-63Hz - 13VDC output, 800mA, 10.4 watts (for use in Japan) |
|
Cover - Main logic PCA cover - Has cut outs for the USB interface socket, parallel interface socket, and power module socket |
|
Cover - Left side case for HP DeskJet 700 Series |
|
Motor - Paper advance motor |
|
PC_Board - Paper encoder PCA - Controls operation of paper motor |
|
Plate - Shift plate assembly - Five plastic gears held in a two piece plastic frame - Attaches to feedroller assembly |
|
Cover - Right side case |
|
Retainer - Left carriage retainer - Protects the carriage assembly from damage during shipment |
|
Spring - Left wall spring (front) - Holds left wall assembly in position |
|
Gear - Feed roller idler gear |
|
Snap - Cap snap - Installed between pallet/link assembly and sled cap assembly - Used to hold the cap spring |
|
Foot - Rubber foot - Replacement rubber foot for the bottom of the printer (four used) |
|
Slider - Integrated slider for carriage assembly |
|
Spring - ESD spring - Installed between ESD blade and carriage PC board |
|
Shield - Paper motor ESD shield |
|
Spring - Latch spring - Provides friction for the knob on the rear cleanout door assembly |
|
Door - Output door - Separates output media from input media |
|
Panel - Paper tray left outer panel (left cheek) - Attaches to left edge of wing frame |
|
Separator - Separator pad for HP DeskJet 700 Series |
|
Pad - Length adjust pad (Poron) - Mounted under the fine length adjuster |
|
Gear - Pick gear for HP Color Copier 170 |
|
Latch - Plastic latch (Y-shaped) |
|
Panel - Paper tray right inner panel (right cheek cap) - Mounts between right wing and right outer panel |
|
Keypad - Keypad assembly |
|
Cover - Service station bonnet - Top cover of the spittoon - Has cutout for pallet/link assembly |
|
Tray - Paper input tray base - Does not include the pressure plate assembly |
|
Pin - Separator peg for HP DeskJet 895C |
|
Guide - Spring guide for HP DeskJet 880C Series |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 240V in South Africa and India) |
|
Cable - Cable assembly - 12-pin (F) connector, 5-pin (F) connector, and 7-pin (F) connector - 43.9cm (17.3in) long |
|
Shield - Main logic PCA EMI shield |
|
Bracket - Paper motor mounting bracket |
|
Guide - Width adjust (Purple) - Holds media against right wall of input tray |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 240V in the United Kingdom) |
|
Spring - Cap spring - Provides upward pressure on the sled cap assembly to seal the parked print cartridges |
|
Spring - Link spring - Provides tension to shaft of pick cam gear |
|
Panel - Paper tray left inner panel (left cheek cap) - Mounts between left wing and left outer panel |
|
Wing - Left wing - Holds printed paper after being ejected |
|
Wing - Right wing - Holds printed paper after being ejected |
|
Cable - Cable assembly - An 11-pin (F) connector to two 3-pin (F) connectors and a 7-pin (F) connector - 36.8cm (14.5in) long |
|
Ferrite_Assembly - Ferrite core for HP OfficeJet K60 |
|
Spring - Drawer spring - Holds input drawer in place |
|
Roller - Pinch roller - Provides downward pressure on media as it passes by upper paper guide |
|
Shaft - Cartridge latch shaft near top of carriage |
|
Shaft - Drive shaft with molded gears on each end |
|
Cam - Pick cam - Controls pressure plate and lever |
|
Spring - Shifter spring - Provides tension on the pivot |
|
Knob - Rear cleanout door knob |
|
Latch - Cartridge latch (Color) - Holds color ink cartridge in place |
|
Panel - Paper tray panel (right cheek) - Attaches to the right edge of the wing frame |
|
Brace - Right backbone brace - Installed on right side of printer base to provide support for backbone |
|
Lever - Paper pusher - Small, spring loaded lever attached to pivot - Pushes against left side of paper to maintain right edge alignment |
|
Blade - ESD blade for HP DeskJet 870C Series |
|
Adjuster - Carriage rod adjuster - Used to support and align the carriage rod (2 used) - This item should be replaced only by trained, experienced service personnel |
|
Snap - Pivot snap - Used to hold pivot to pick feed roller shaft |
|
Backbone - BacKBone - Large metal item where the main logic PCA and the carriage drive motor are mounted - This item should be replaced only by trained, experienced service personnel |
|
Carriage - Ink cartridge carriage |
|
Lever - Banner lever - Used to choose either single sheet paper or continuous feed (Banner) paper |
|
Pallet - Pallet/link assembly - Installed between spittoon and sled cap assembly - Mounting platform for the wiper and capping systems parts |
|
Spring - Belt tension spring - Provides tension for carriage belt |
|
Spring - Left wall spring (rear) - Provides pressure against media |
|
Lever - Pressure plate lever - Transfers upward pressure from the separator lifter to the kicker |
|
Retainer - Felt retainer - Holds the lubricating felt to the side of the carriage |
|
Sled - Sled cap assembly - Top cover of the service station assembly - Includes print cartridge caps (gaskets which keep the cartridges from drying out when not printing) |
|
Rod - Carriage rod - Shaft that the carriage assembly rides on - This item should be replaced only by trained, experienced service personnel |
|
Holder - Right carriage restraint (holder) - Used to protect the carriage assembly from damage during shipment |
|
Spring - Rear roller spring - Flexible axle for rear roller |
|
Spring - Envelope spring - Holds envelopes in position for picking |
|
Gear - Encoder gear for HP Color Copier 260 |
|
Tray - Paper input tray pressure plate |
|
Link - Kicker bar cam link (spring loaded) |
|
Plate - Belt Attachment Plate - Mounted to back of Ink Cartridge Carriage Assembly - Used to attach the Carriage Drive Belt |
|
Lifter - Separator lifter - Used to lift the separator peg |
|
Gear - Transfer gear (double gear) |
|
Cable - Carriage assembly flex cable - 40.3cm (15.9in) long |
|
Channel - Width adjust channel |
|
Spring - Wing torsion spring - Provides pressure on the wing during paper output |
|
Frame - Wing frame - Chassis for in/out tray components |
|
Spring - Separator spring - Provides pressure between separator assembly and the center drive roller |
|
Spring - Encoder spring - Provides tension for encoder strip |
|
Spring - EOR tension spring - Maintains tension on wear strip |
|
Plate - Back Plate - Holds Latch Spring, Knob and Latch Components of Rear Cleanout Assembly |
|
Roller - Rear roller (Black) - Between paper and rear paper guide |
|
Guide - Lower guide - Platform for seperator peg, spring and pad |
|
Guide - Encoder disk guide |
|
Brace - Left backbone brace - Provides support for backbone |
|
Wiper - Wiper assembly - Metal base with plastic wipers |
|
Tray - Paper input tray assembly (partial) - Includes only base of tray and pressure plate assembly |
|
Paper_Stacker - Kicker - Restacks paper in stack after top sheet is picked |
|
Washer - Felt washer - Used to lubricate the carriage rod |
|
Clip - Service station ESD grounding clip |
|
Gear - Cluster gear (large gear) |
|
Flag - OOPS flag - Media sensor - Mounts on the top right edge of the upper paper guide |
|
Power_Module - Wall mount power supply module (Leader Electronics 48130625HK) - 200VAC input, 48-52Hz - 13VDC output, 625mA (Hong Kong) |
|
Spring - Paper length adjuster spring - Provides tension for paper input length adjuster |
|
Cam - Drawer cam - Short, spring loaded lever attached to the base of the wing frame - Used to draw input tray into position |
|
Vent - Cap vent - For equalizing the print cartridge capping pressure |
|
Gear - Feed roller cluster gear |
|
Door - Top/front access door assembly - Print cartridge access door with blueberry colored window - Includes installation instructions |
|
Spring - Paper pusher spring - Maintains alignment in paper tray |
|
Spring - Pinch spring - Provides tension on upper paper guide |
|
Latch - Cartridge latch (Black) - Holds black ink cartridge in place |
|
Spring - Paper stacker (kicker) spring |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 100V in Japan) |
|
Cable - IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) - 3.0m (9.8ft) long |
|
Guide - Length adjuster - Media input length adjuster |
|
Stop - Fine paper length adjuster (Purple) - Holds paper firmly against the back of the paper input tray |
|
Support - Upper paper guide support - Base for upper paper guide |
|
Brace - Left wall brace - Provides support for left wall |
|
Stickers - Round re-stickable InkJet stickers - HP bright white 6.35cm (2.5in) round stickers with 3M 'Post-it' adhesive - A size (8.5 x 11-inches) - 10 sheets per package with nine stickers per sheet |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 220V in China) |
|
Power_Cord - Power cord (Quartz Gray) - 2-wire, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 240V in Australia and New Zealand) |
|
Guide - Left wall pusher - Pushes against left side of media to maintain correct edge alignment |
|
Turnaround_Assembly - Turnaround assembly - Provides carriage belt tension - Does not include spring |
|
Film - Premium InkJet transparency film - A4 size (21.0cm x 29.7cm) - 20 sheets per package |
|
Cartridge - No. 15 Black Ink Print Cartridge - 21 ml Ink (for USA) |
|
Paper - Media for HP C6465A |
|
Paper - Deluxe glossy photo paper - A size (8.5 x 11-inches) - 20 sheets per pack |
|
DeskJet - DeskJet 843C Printer |
|
Paper - Media for HP C6429C |
|
Service_Guide_PH - HP DeskJet 843C Printer Reference Guide - Contains information such as product information, operation overview, paper behavior, mainenance, ink safety, and removal / replacement of parts |
|
Cartridge - InkJet Cartridge 15 Black LAR) |
|
Cartridge - No. 17 Tri-color ink print cartridge (Europe) |
|
Manual - DeskJet and DeskWriter service manual on CD-ROM - Version 4.1 |
|
Cartridge - InkJet Cartridge 15 Black EUR) |
|
Cartridge - No. 15 Black ink print cartridge - 25 ml ink (Asia Pacific) |
|
Paper - Brochure and flyer paper - Glossy on both sides - A size (8.5 x 11-inches), 98 brightness - 50 sheets |
|
Paper - Media for HP C5894A |
|
Paper - Media for HP C8136A |
|
Cartridge - InkJet Cartridge 15 Black Can |
|
Paper - Media for HP Q5761A |
|
Power_Cord - Power cord (Flint Gray) - 2-wire, 18 AWG, 1.8m (6.0ft) long - Has straight (F) C7 receptacle (for 220V in Europe, Asia Pacific, Germany, Spain, France, Netherlands, Switzerland, Italy, and Portugal) |
|
Paper - Media for HP C8136A |
|
Paper - Media for HP C6428A |
|
Paper - InkJet non-glossy LX paper - A4 size (21.0cm x 29.7cm) - 200 sheets per package |
|
Paper - Media for HP C8244A |
|
Cartridge - No. 17 Tri-color ink print cartridge (Asia/Pacific) |
|
Paper - Printable Expressions all occasions card kit - Includes 20 greeting cards and envelopes, and a CD-ROM with 24 original pieces of art |
|
Cartridge - HP 15 Black InkJet Cartridge LAR |
|
Cartridge - No. 17 Tri-color ink print cartridge (Latin America) |
|
Paper - HP Photo Greeting Cards (Glossy) - A size (8.5 x 11-inches) - 10 scored half-fold glossy cards and envelopes |
|
Paper - Greeting card paper pack (White) - A size (8.5 x 11-inches) - Includes 20 sheets and 20 envelopes |
|
Paper - Media for HP C5894A |
|
Paper - Media for HP C8127A |
|
Cartridge - HP 15 Black InkJet Cartridge EUR |
|
Paper - Premium Photo Paper (Glossy) - A size (8.5 x 11-inches) - 15 sheets |
|
Paper - Media for HP C6429C |
|
Cartridge - HP 15 Black InkJet Cartridge Can |
|
Cartridge - InkJet Cartridge 15 Black AP |
